Intel SG-80, SG-81 user manual Front Panel Audio Connection Header FPIO-AUDIO1

Page 18

2-8

Chapter 2

 

 

 

 

2.3.6.Front Panel Audio Connection Header (FPIO-AUDIO1)

This header provides the connection to audio connector at front panel.

To use the audio connector at front panel, remove all the jumpers on this header, and then connect to front panel by the extension cable provided with the chassis.

To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at pin 5-6, and pin 9-10 (default setting).

Pin

Signal Name

Function

 

1

AUD_MIC

Front Panel Microphone input signal

 

2

AUD_GND

Ground used by Analog Audio Circuits

 

3

AUD_MIC_BIAS

Microphone Power

 

4

AUD_VCC Filtered

+5V used by Analog Audio Circuits

 

 

 

 

 

5

AUD_F_R

Right Channel audio signal to Front Panel

 

 

 

 

 

6

AUD_RET_R

Right Channel Audio signal to Return from

 

Front Panel

 

 

 

 

 

 

 

 

7

REVD

Reserved

 

 

 

 

 

8

Key

No Pin

 

 

 

 

 

9

AUD_F_L

Left Channel Audio signal to Front Panel

 

10

AUD_RET_L

Left Channel Audio signal to Return from Front

 

Panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SG-80 Series

Image 18
Contents SG-80 Series Page Table of Contents Chapter Driver Installation Appendix A. How to Get Technical SupportFeatures & Specifications Miscellaneous Model Chipset FeaturesBack Panel I/O Product ListLayout Diagram SG-80 Layout Diagram SG-81 Jumpers & Connectors Description Jumpers Description Default SettingConnectors Description SG-80 Series Hardware Setup CPU SocketSystem Memory Dimm Module Total MemoryTotal System Memory Connectors, Headers, and Switches ATX Power Connectors ATXPOWER, ATX12VFAN Connectors CPUFAN, SYSFAN, Pwrfan Pin 2-3 shorted default Normal operation Cmos Memory Clearing Header CcmosFront Panel Switches & Indicators Connection Headers PANEL1 Pin DefinitionPin Signal Name Function Additional USB Port Connection Header USB3, USB4Front Panel Audio Connection Header FPIO-AUDIO1 Accelerated Graphics Port Slot AGP1 Internal Audio Source Connectors CD1, AUX1 Floppy Disk Drive Connector FDC IDE Disk Drive Connectors IDE1, IDE2 Serial ATA connectors SATA1, SATA2 External I/O Panel About the Setup Utility Standard ConfigurationExits the current menu Updating the Bios Using Bios Standard Cmos FeaturesDate and Time IDE Devices None IDE HDD Auto-DetectionIDE Channel 1/2 Master/Slave/ IDE DriveAuto Drive A/Drive B 1.44M, 3.5 in./None Access Mode AutoFloppy 3 Mode Support Disabled Video EGA/VGAAdvanced Bios Features CPU FeatureHard Disk Boot Priority Quick Power On Self Test Enabled CPU L3 Cache EnabledHyper-Threading Technology Enabled First/Second/Third Boot Device Floppy/Hard Disk/CDROMSecurity Option Setup Advanced Chipset FeaturesATA 66/100 IDE Cable Msg. Enabled Small LogoEPA ShowDram CAS Latency Dram Clock/Timing ControlDram Timing Control RAS Active Time tRASAGP Fast Write Support Disabled RAS to CAS Delay tRCDGraphic Window WR Combin Enabled AGP & P2P Bridge ControlOnChip AGP Control System Bios Cacheable DisabledVideo RAM Cacheable Disabled AGP Data Rate AutoIntegrated Peripherals OnChip IDE DeviceOnChip Sata Controller Enabled IDE DMA Transfer Access EnabledIDE Burst Mode Enabled Serial ATA Mode IDEOnChip LAN Controller Enabled OnChip USB Controller EnabledOnChip AC97 Controller Enabled LAN Boot ROM DisabledOnboard SuperIO Device Onboard FDC Controller EnabledParallel Port Mode ECP Onboard Serial Port 1 3F8/IRQ4Onboard 1394 Device Enabled Power Management SetupECP Mode Use DMA Init Display First PCI SlotPower On by PS2 Mouse Disabled Resume by USB from S3 DisabledPower On by PS2 Keyboard Hot Key Wakeup By Ring DisabledPnP/PCI Configurations Resources Controlled By AutoESCDPCI/VGA Palette Snoop Disabled IRQ ResourcesPC Health Status CPU Shutdown Temperature DisabledSystem Component Characteristics PIRQ0 Use IRQ No. ~ PIRQ7 Use IRQ No. AutoSpread Spectrum Enabled Load Fail-Safe Defaults OptionAuto Detect DIMM/PCI Clk Enabled Frequency ControlLoad Optimized Defaults Option Set PasswordSave & Exit Setup Option Exit Without SavingSG-80 Series Driver Installation Manual Utility Setup ItemsDrivers Browse CDHow to Get Technical Support User’s ManualAppendix a SG-80 SeriesJan van Riebeeckweg 15, 5928LG, Venlo Technical Support Form