Intel 8 LAN manual LED 1 Configuration and Power Management Word 17h

Page 15
LED 1 Configuration and Power Management (Word 17h)

ICH8—NVM Information Guide

1.4.19LED 1 Configuration and Power Management (Word 17h)

This field specifies the default values for the LEDCTL register fields controlling the LED1 (LINK_1000) output behaviors and the OEM fields defining the PHY power management parameters loaded to the PHY_CTRL register.

Table 15.

LED 1 Configuration and Power Management (Word 17h)

 

 

 

 

 

 

 

Bit

Name

Default

 

Description

 

 

 

 

 

 

 

 

 

This bit enables Smart Power Down in back-to-back link setup.

 

15

B2B Enable

1b

0b = B2B disabled.

 

 

 

 

1b

= B2B enabled.

 

 

 

 

 

 

 

 

 

GbE Disable (in all power states)

 

14

GbE Disable

0b

0b = GbE enabled.

 

 

 

 

1b

= GbE disabled.

 

 

 

 

 

 

13:12

Reserved

00b

These bits are reserved and should be set to 00b.

 

 

 

 

 

 

 

GbE Disable in non-

 

GbE Disable (in all power states except D0a)

 

11

1b

0b

= GbE enabled.

 

D0a

 

 

 

1b

= GbE disabled.

 

 

 

 

 

 

 

 

 

 

 

 

 

The Low Power Link Up enables link at the lowest speed supported

 

 

LPLU Enable in non-

 

by both link partners in non-D0a states. This bit must be set if

 

10

1b

LPLU Enable bit is set.

 

 

D0a

 

0b

= Low Power Link Up is disabled.

 

 

 

 

 

 

 

 

1b

= Low Power Link Up is enabled in all non-D0a states.

 

 

 

 

 

 

 

 

 

The Low Power Link Up enables link at the lowest speed supported

 

 

 

 

by both link partners in all power states. This bit enables a

 

9

LPLU Enable

0b

decrease in link speed in all power states.

 

 

 

 

0b

= Low Power Link Up is disabled.

 

 

 

 

1b

= Low Power Link Up is enabled in all power states.

 

 

 

 

 

 

 

8

SPD Enable

1b

0b

= PHY Smart Power Down mode is disabled.

 

1b

= PHY Smart Power Down mode is enabled.

 

 

 

 

 

 

 

 

 

 

 

 

 

This bit indicates the initial value of the LED1_BLINK field.

 

7

LED1 Blink

0b

0b = LED1 is non-blinking (recommended).

 

 

 

 

1b

= LED1 is blinking.

 

 

 

 

 

 

 

 

 

This bit indicates the initial value of the LED1_IVRT field.

 

6

LED1 Invert

0b

0b = LED1 has an active low output.

 

 

 

 

1b

= LED1 has an active high output.

 

 

 

 

 

 

 

 

 

This bit defines the LED1 blink mode:

 

5

LED1 Blink Mode

0b

0b

= Blink at 200 ms on and 200 ms off.

 

1b

= Blink at 83 ms on and 83 ms off.

 

 

 

 

 

 

 

 

This field should be identical to LED0 Blink Mode.

 

 

 

 

 

 

 

 

 

Enable Filtered Activity LED (while operating with the 82562V)

 

 

 

 

When set to 0b, the activity LED is activated by the PHY.

 

4

Filtered ACT LED

0b

When set to 1b, the activity LED is driven by Tx activity or Rx

 

 

 

 

traffic that match any of the MAC's MAC addresses.

 

 

 

 

For the 82566, this bit is reserved and should be set to 0b.

 

 

 

 

 

 

 

 

 

These bits represent the initial value of the LED1_MODE field,

 

 

 

 

which specifies the event, state, or pattern displayed on LED1

 

3:0

LED1 Mode

0111b

(LINK_1000) output. Table 16 defines the values for LED1 Mode.

 

 

 

 

A value of 0111b indicates that a 1000 Mb/s link is established and

 

 

 

 

maintained.

 

 

 

 

 

 

The following table lists the LED modes defined in bits 3:0 of this word.

15

Image 15
Contents 316234-006Revision JanuaryIntel Corporation P.O. Box 5937 Denver, CO Tables ContentsRevision History 1.2NVM Programming Procedure Overview 1.0Non-VolatileMemory NVM1.1Introduction Figure 1. LAN NVM Regions BIOS Region ME Region GbE Region Flash DescriptorRegion 1.3EEUPDATE Utility 1.3.1Command Line ParametersExample 1. EEUPDATE /D file1.eep Table 1. LAN NVM Address Map 1.4LAN NVM Format and Contents1.4.1Ethernet Individual Address Words 00h - 02h 1.4.2Reserved Word 03hReserved Word 03h 1.4.6Reserved Word 07h 1.4.3Reserved Word 04h1.4.4Image Version Information Word 05h 1.4.5Reserved Word 06hPCI Initialization Control Word Word 0Ah 1.4.8PCI Initialization Control Word 0Ah1.4.9Subsystem ID Word 0Bh 1.4.10Subsystem Vendor ID Word 0Ch1.4.12Vendor ID Word 0Eh 1.4.14LAN Power Consumption Word 10hLAN Power Consumption Word 10h 1.4.11Device ID Word 0DhShared Initialization Control Word 13h 1.4.15Shared Initialization Control Word 13hExtended Configuration Word 1 Word 14h 1.4.16Extended Configuration Word 1 Word 14h1.4.17Extended Configuration Word 2 Word 15h 1.4.18Extended Configuration Word 3 Word 16hLED 1 Configuration and Power Management Word 17h LED Modes 1.4.20LED 0 and 2 Configuration Defaults Word 18h1.4.22 LED 0 and 2 Configuration Defaults Word 18h1.4.21 Future Initialization Word 1 Words 19h1.4.23.1Boot Agent Main Setup Options Word 30h Table 18. Boot Agent Main Setup Options1.4.23PXE Words Words 30h - 3Eh prompt message appears, if enabled by DIM NVM Information Guide-ICH8 Disable Protocol Select 1.4.24Checksum Word 3Fh 1.4.23.4IBA Capabilities Word 33hTable 21. IBA Capabilities LAN NVM Contents Appendix A ICH8 NVM Contents and Sample ImagesA.1 82566DM NVM Image with ICH8 A.2 82566MM NVM Image with ICH8M A.3 82566MC NVM Image with ICH8 A.4 82562V NVM Image with ICH8 Note This page intentionally left blank