Lantronix MPS1-2, MPS1-T, MPS100 manual Table B-6 PostScript Troubleshooting, Bitmap Graphics

Page 67

 

Troubleshooting

 

Table B-6:PostScript Troubleshooting, cont.

 

 

Area to Check

Explanation

 

 

 

 

Port Counters

If PostScript jobs appear to print but nothing comes out of the

 

printer, verify the amount of data sent from the host. Issue the

 

appropriate print command from the host system. After the job

 

has completed, use the Show Port 1 Counters command.

 

The bytes output value should be approximately 171 bytes

 

greater than the size of the Þle on the host system. These

 

numbers are only approximate, but will show that data is

 

ßowing to the printer.

 

 

B.6.1 Bitmap Graphics

If Þles that contain embedded bitmap graphics print incorrectly, it is because the bitmaps are being sent as actual binary data and binary data cannot be printed via serial or parallel interfaces.

Most major application packages have provisions to print using either Òbinary postscriptÓ (for printers connected to the network via LocalTalk) or Òhex postscriptÓ (for printers connected to the network via a serial port or parallel port). If your application does not have this provision, ask the application vendor for an upgrade version or ÒpatchÓ that will add the Òhex postscriptÓ function.

B - 7

Image 67
Contents Print Server Installation Guide Page Contents Page Introduction How to Use This Manual Installation Product Description Installation Installation Page Getting Started EZWebCon Configuration Services Incoming LoginsGetting Started TCP/IP Configuration Using EZWebCon Setting the IP AddressUsing a Directed Ping Packet \ ARP -S 192.0.1.228 00-80-A3-XX-XX-XX \ Ping TCP/IP Configuration Using the Command Line Interface Using a DHCP, BOOTP, or Rarp ReplyTCP/IP Configuration LPR on Windows NT Select the Add Port button and click Next TCP/IP Configuration Select the manufacturer and printer type Enter the queue name Page Test the printer LPR on Unix Hosts Lpr -Pmpsprt /etc/hosts LPR on AIX Hosts Lp -dmpsprt filename LPR on HP Hosts LPR on SCO Unix Hosts TCP/IP Configuration Rtel Functionality 1TCP Troubleshooting Unix Host TroubleshootingArea to Check Page NetWare Configuration Obtaining an NDS License Reboot the MPS From the Menu Bar, select Tools Print Services Quick Setup Creating NDS Print Queues Using Pconsole Use the Show Protocols NetWare Access command NetWare Host Troubleshooting1NetWare Host Troubleshooting Bindery Mode 2NetWare Host Troubleshooting NDSType Show Protocol NetWare NDS. This command 2NetWare Host Troubleshooting NDS,Protocol NetWare Reset command 3NDS Errors from the File ServerFailure code Failure code meaning Bit Failure Code Meaning Remedy 4NDS Printing ErrorsPage Printing Directly to a Port LAT ConfigurationPrint to the queue 1Troubleshooting LAT ConÞgurations Using a Port LAT Host TroubleshootingPage Bitronics AppleTalk ConfigurationAppleTalk Zones Macintosh Services1AppleTalk Host Troubleshooting AppleTalk Host TroubleshootingTest Service PostScript Count n command. This Page DLC Configuration LAN Manager/DLC ConfigurationServer Configuration Select Hewlett-Packard Network Port and click New Port Host ConfigurationContact Information LANtronix Table B-1Error Messages Troubleshooting Power-Up TroubleshootingMessage Diagnosis/Remedy Table B-2General Printing Problems Printing ProblemsEtc/hosts Þle Bootp TroubleshootingTable B-3BOOTP Troubleshooting Etc/services ÞleTable B-4DHCP Troubleshooting Dhcp TroubleshootingUse the DeÞne Server Dhcp Enabled command Table B-5RARP Troubleshooting Rarp TroubleshootingTable B-6PostScript Troubleshooting PostScript ProblemsBitmap Graphics Table B-6 PostScript Troubleshooting,Page Pinouts Parallel Information Page Updating Software Updating Via the Web Updating Using FTP Updating Using the BBS Reloading Software Reloading Sequence 3 TCP/IP NetWareUpdating Software 4 MOP Table D-1 Flash ROM Troubleshooting Troubleshooting Flash ROM UpdatesProtocol Area to Check MOP Table D-1Flash ROM Troubleshooting,Temperature Limitations Specifications Power RequirementsPower Supply Cord Relative Humidity Limitations Altitude LimitationsKm 30,000 ft Frequently-used Commands Table F-1Frequently-used Server Commands Server CommandsCommand Options Description Define Server Login Password Table F-1Frequently-used Server Commands,Help option Define Service DLC Endis Telnetport string NoneOption Table F-2Port Commands Port CommandsXON Table F-2Port Commands,Table F-3Protocol Commands Protocol CommandsDscontext string Table F-3Protocol Commands,Define Proto Native Warranty Statement Declaration of Conformity Numerics IndexIndex-ii Index-iii
Related manuals
Manual 74 pages 19.89 Kb