Lenovo 8142, 8426 Setting, changing, and deleting a password, Using Security Profile by Device

Page 43

Attention

Make sure that the IDE Drive Master password is stored in a safe place. If both the IDE Drive User password and the IDE Drive Master password are lost or forgotten, the IDE hard disk drive must be replaced.

If both the IDE Drive User Password and the IDE Drive Master Password are to be set, the IDE Drive Master Password must be set before setting the IDE Drive User Password.

Setting, changing, and deleting a password

To set, change, or delete a password, do the following:

Note: A password can be any combination of up to seven characters (A- Z, a-z, and 0-9).

1.Start the Setup Utility program (see “Starting the Setup Utility program” on page 25).

2.From the Setup Utility program menu, select Security.

3.Select Set Passwords. Read the information displayed on the right side of the screen.

Using Security Profile by Device

Security Profile by Device is used to enable or disable user access to the following devices:

IDE controller

When this feature is set to Disable, all devices connected to the

 

IDE controller (such as hard disk drives or the CD-ROM drive)

 

are disabled and will not be displayed in the system

 

configuration.

Diskette Drive Access

When this feature is set to Disable, the diskette drive cannot be

 

accessed.

Diskette Write Protect

When this feature is set to Enable, all diskettes are treated as if

 

they are write-protected. You can read the diskette, but you

 

cannot write to the diskette.

To set Security Profile by Device, do the following:

1.Start the Setup Utility program (see “Starting the Setup Utility program” on page 25).

2.From the Setup Utility program menu, select Security.

3.Select Security Profile by Device.

4.Select the desired devices and settings and press Enter.

5.Return to the Setup Utility program menu and select Exit and then Save Settings.

Selecting a startup device

If your computer does not start up (boot) from a device such as the CD-ROM, diskette, or hard disk as expected, use one of the following procedures to select a startup device.

Chapter 2. Using the Setup Utility program 27

Page 42 Page 44
Image 43
Page 42 Page 44
Contents User Guide Types 8095, 8096, 8141 Types 8145, 8420, 8421 Page User Guide Types 8095, 8096, 8141 Types 8145, 8420, 8421 Page Contents Iv User Guide Conditions that require immediate action Important safety informationService General safety guidelinesExtension cords and related devices Power cords and power adaptersBatteries Plugs and outletsHeat and product ventilation CD and DVD drive safetyLithium battery notice Additional safety informationTo connect To disconnect Laser compliance statement Modem safety informationPower supply statement Information resources OverviewXiv User Guide Features Installing optionsMemory Operating systems, preinstalled varies by model type Specifications Tools required Available optionsHandling static-sensitive devices Installing external options Locating the connectors on the front of your computer Locating the connectors on the rear of your computer Obtaining device drivers Connector DescriptionRemoving the cover Identifying parts on the system board Locating componentsInstalling memory Installing options What to do next Installing adaptersWhat to do next Drive specifications Installing internal drivesInstalling a drive User Guide Connecting the first optical drive Connecting a serial ATA hard disk drive Installing security featuresChanging the battery Password protectionPadlock loop User Guide Replacing the cover and connecting the cables Erasing a lost or forgotten password clearing CmosUser Guide Using passwords Using the Setup Utility programStarting the Setup Utility program Viewing and changing settingsIDE Drive Master Password User passwordAdministrator password IDE Drive User PasswordUsing Security Profile by Device Setting, changing, and deleting a passwordSelecting a startup device Selecting a temporary startup device Exiting from the Setup Utility programChanging the startup sequence System programs Updating flashing Bios from a disketteUpdating flashing Bios from your operating system Appendix A. Updating system programsClick Continue Click Downloads and drivers Recovering from a POST/BIOS update failureCleaning an optical mouse Appendix B. Cleaning the mouseCleaning a mouse with a ball User Guide Basic AT commands Appendix C. Manual modem commandsInternal speaker on until carrier detected Low speaker volumeSet Pulse dial as default Set Tone Dial as defaultExtended AT commands MNP/V.42/V.42bis/V.44 commands Fax Class 2 commands Fax Class 1 commandsVoice commands Appendix C. Manual modem commands User Guide Appendix D. Notices Trademarks Television output noticeIndex Page Page Part Number 19R0462
Top Page Image Contents