Sanyo PLC-XK3010 owner manual Examples Type and contents of alert mail

Page 28

Chapter 3 Basic Setting and Operation

Examples: Type and contents of alert mail

When the projector has an abnormality, the following alert messages are sent to the regis- tered E-mail address according to your selected condition. Administrator or user can take an efficient action quickly by receiving this message. This is very useful to maintain and service the projector.

The following are examples of received messages.

●When internal PJ temperature is too high:

TITLE: Message from projector

Projector Model Name: model name

TCP/IP: 192.168.1.201 Projector Name: Proj05

It sends you following message.

*The Projector lamp is turned off, because internal projector temperature is too high. Wait for the completion of the cooling process and make sure the projector has been turned into Standby. Then turn the projector on again.

If the Indicator continues flashing, check the air filter for dust accumulation.

●When PJ needs service:

TITLE: Message from projector

Projector Model Name: model name

TCP/IP: 192.168.1.201 Projector Name: Proj05

It sends you following message.

*Maintenance requirement from Projector is detected.

Check up LED status of projector and consult with the dealer.

	MCI	3.3V	OK	Error information
	MAIN	ALL	NG

✐The projector lamp was turned off, because the projector power circuit failed.

Unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the error information.

●When PJ lamp replacement time is reached:

TITLE: Message from projector

Projector Model Name: model name

TCP/IP: 192.168.1.201 Projector Name: Proj05

It sends you following message.

*The projector lamp has reached replacement time. Lamp ON 3000 h

✐Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every power- on of the projector. This alert mail will not be sent when unchecking the mail sending condition "When PJ lamp replacement time is reached".

28

Image 28

Contents Wired Setting Projector Set-up and Operation Network Set-up and OperationCompliance Federal Communications Commission NoticeAddress Telephone No 818998-7322Safety instructions Table of contents Chapter Features Web Management function +p.31Network specifications of the projector Required operating environment for computersUse of this manual Expression/AbbreviationTrademarks Connect the LAN and set the configuration Flow of installationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Numerical value is a setting example Network PIN codeNetwork factory default Wired LAN factory default settings Chapter Basic Setting and Operation Login Login the setting page of the projectorEnter the IP address Display of main setting Main setting page in the displaySub menu tab Switches the sub menu tab Main menu SettingHow to use the setting Example of the settingSelect an item by selecting a radio button Select items by ticking on check boxesInitial setting Network PIN code setting PJLink and password settingTo 32 alphanumeric characters can be used for the password Whats PJLink?Displays the selected LAN mode Network configurationSets Dhcp configuration ON/OFF Mail setting Setting Smtp server and administrator address Registering and deleting E-mail addressesSetting Smtp authentication Setting POP serverOption selection for sending alert mail OptionExamples Type and contents of alert mail Snmp setting Trap check/delete Up to 99,999 hours can be set for the time settingClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector Power control and status check Service in needDisplays the status of the projectors power. Refer to next Popup confirmation windowAbout projector condition Status DescriptionControl InputSystem Item DescriptionSound Suppresses the sound. ON, OFFImage adjustment PC adjustment Setting up the projector Screen settingSetting Sets the black out image temporarily. ON, OFF Sets the image to freeze mode. ON, OFFInformation InformationItems Description Indication of the lamp status StatusControlling the Projector Chapter Appendix Peer-To-Peer connection Examples of connectionTo another network Gateway Router installed in the network Entrance hallControl Use of telnetUse the IP address assigned to the projector Command Function Active Script/JavaScript enable Web browser settingProxy setting Windows XP Professional Examples OS/BrowsersInternet Explorer Proxy setting JavaScript Setting Netscape NavigatorMAC OS X v SafariWhy doesn’t the setting page appear in my web browser? How can I restrict access from the computerHow can I install several projectors? Why am I not receiving E-mail alert messages? Why cant be turned on/off with web browser?Ting What is the MAC address assigned to the projector? What are the rules for IP address assignment?Can I update the firmware of the projector SO-KT8AE