Sanyo PLC-XK3010 owner manual Network configuration, Displays the selected LAN mode

Page 24

Chapter 3 Basic Setting and Operation

Network configuration

Click Network on the main menu. The following setting page is displayed. The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) and projector name are set up on this menu.

The IP address and Subnet Mask have been configured already in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds.

Item	Description
LAN mode	Displays the selected LAN mode
DHCP	Sets DHCP configuration (ON/OFF).
IP address	Sets IP address of the projector
Subnet mask	Sets Subnet mask. Normally sets 255.255.255.0
Default gateway*1	Sets IP address of the default gateway (Router)
DNS*2	Sets IP address of the DNS server. Must be set when using the e-mail function

Projector name*3.Sets name of the projector. (64 characters maximum)

✐You must use the number specified by your administrator. The address must be entered as a group with four numbers split by a dot like [192.168.001.101].

*1 Set [0.0.0.0] if the network does not provide the gateway (router).

*2 Set [0.0.0.0] if you do not use the function E-Mail alert.

*3 If you use the DNS server, register the host name registered to the DNS server as a projector name. You can access with this projector name from any computers in your network. If you do not use the DNS server, access with the assigned IP address to the projector.

*All the network setting will reset to the default when setting [0.0.0.0] of the IP Address.

*If you make incorrect settings, you cannot find out the new network settings. Be careful to set up

24

them correctly, otherwise you cannot connect to the projector. It is recommended to make a note of them.

Image 24

Contents Wired Setting Projector Set-up and Operation Network Set-up and OperationCompliance Federal Communications Commission NoticeAddress Telephone No 818998-7322Safety instructions Table of contents Chapter Features Web Management function +p.31Network specifications of the projector Required operating environment for computersExpression/Abbreviation Use of this manualTrademarks Flow of installation Connect the LAN and set the configurationNetwork Configuration has completed Preparation Setup Procedures Connecting to the LAN line Description Numerical value is a setting example Network PIN codeNetwork factory default Wired LAN factory default settings Chapter Basic Setting and Operation Login the setting page of the projector LoginEnter the IP address Display of main setting Main setting page in the displaySub menu tab Switches the sub menu tab Main menu SettingHow to use the setting Example of the settingSelect an item by selecting a radio button Select items by ticking on check boxesInitial setting Network PIN code setting PJLink and password settingTo 32 alphanumeric characters can be used for the password Whats PJLink?Network configuration Displays the selected LAN modeSets Dhcp configuration ON/OFF Mail setting Setting Smtp server and administrator address Registering and deleting E-mail addressesSetting Smtp authentication Setting POP serverOption selection for sending alert mail OptionExamples Type and contents of alert mail Snmp setting Up to 99,999 hours can be set for the time setting Trap check/deleteClick Set button if you tick or un-tick the check box on a Chapter Controlling the Projector Power control and status check Service in needDisplays the status of the projectors power. Refer to next Popup confirmation windowAbout projector condition Status DescriptionControl InputSystem Item DescriptionSound Suppresses the sound. ON, OFFImage adjustment PC adjustment Setting up the projector Screen settingSetting Sets the black out image temporarily. ON, OFF Sets the image to freeze mode. ON, OFFInformation InformationItems Description Indication of the lamp status StatusControlling the Projector Chapter Appendix Examples of connection Peer-To-Peer connectionTo another network Gateway Router installed in the network Entrance hallUse of telnet ControlUse the IP address assigned to the projector Command Function Web browser setting Active Script/JavaScript enableProxy setting Examples OS/Browsers Windows XP ProfessionalInternet Explorer Proxy setting JavaScript Setting Netscape NavigatorMAC OS X v SafariWhy doesn’t the setting page appear in my web browser? How can I restrict access from the computerHow can I install several projectors? Why cant be turned on/off with web browser? Why am I not receiving E-mail alert messages?Ting What is the MAC address assigned to the projector? What are the rules for IP address assignment?Can I update the firmware of the projector SO-KT8AE