Sanyo POA-PN02 owner manual Compliance, Federal Communication Commission Notice

Page 2

Compliance

Federal Communication Commission Notice

This equipment has been tested and found to comply

 

 

 

 

with the limits for a Class B digital device, pursuant to

SANYO

POA-PN02

part 15 of the FCC Rules. These limits are designed

 

Tested To Comply

to provide reasonable protection against harmful

 

With FCC Standards

interference in a residential installation. This equip-

FOR HOME OR OFFICE USE

ment generates, uses and can radiate radio frequency

 

 

energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installa- tion. If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encour- aged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise speci- fied in the manual. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Numbers

: POA-PN02

Trade Name

: Sanyo

Responsible party

: SANYO FISHER COMPANY

Address

: 21605 Plummer Street, Chatsworth, California 91300

Telephone No.

: (818)998-7322

 

 

 

 

 

 

 

 

 

 

CAUTION ON USE IN NETWORK

-When you receive an alert e-mail from the projector, you must check the projector immediately. Fire or accident may result if the projector is used in an abnormal condition.

-When you install the projector at remote location and use it through the network, you must perform the safety inspections periodically. In this case you must pay attention to the change of environment in which you installed the projector. It may cause fire or an accident depending on the change of environment.

CAUTION

SANYO Electric Co. Ltd assumes no responsibility for the loss or damage of data or damage of the computer caused by use of this product.

2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents PJ-Net Organizer plus Model No. POA-PN02Compliance Federal Communication Commission NoticeContents Use of Serial Port Network Viewer & CaptureControlling the Multi-Projectors AppendixAChapter Preparation Network Viewer function FeaturesNetwork Capture function Web Management function Mail Alert functionControl port ready for external equipment via network Automatic On/Off using Clock functionMulti-control function Operating Environment Before use Package containsTrademarks Expression/AbbreviationUse of this manual Software License Agreement Software License AgreementChapter Installation Installation of the software p.22-24 Flow of installationInstallation and network configuration p.16-21 Function of the Network Unit p.15Name and function of each part Installation and Network configuration MountingConnection of LAN cable Confirmation of the network menu Network configurationConfigure the network Selection of network menu NetworkCompleting of installation Configuration for IP Address/ Sub net/ Gateway*/DNSHow to enter the numbers Restart the Network UnitPassword setting How to enter the numbers with point buttonsHow to enter the numbers with the screen 10-key pallet Installing the software Network Viewer & Capture installationNetwork Viewer File Converter Installed softwareNetwork Capture Network Viewer Program EditorFile Converter 2 Installation Installed software and placesChapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorSelect a display mode and login Display of main setting Main setting page in the Graphic Mode displayMain setting page in the Text Mode display Initial Settings Language SettingTemperature unit setting Use of BatteryDate/Time Setting Name the projector Network ConfigurationConfigure the network Mail Setting Smtp Server*1Registering and deleting E-mail addresses Option selection for sending alert messageExamples Type and contents of alert mail When the internal power circuit is failed Chapter Controlling the Projector Power on/off the projector Check the status of projector ItemsControl the projector Input DescriptionPC Adjustment PictureSave a Set Load a SetAvailable selection when the Y, Cb/Pb, Cr/Pr input System AdjustmentAvailable selection when the VIDEO/S-VIDEO input Image Adjustment AdjustmentSave an image adjustment value Load an image modeScreen SoundSetting Confirmation window How to set the Timer Set a day or dateSet a time Check the Timer eventsGetting the current time Select an event on or OFFCancel the timer Service Name the current setting Save Actual AdjustmentAdjust and set the controls Save the current settingCheck the Save items Load a control set Control the projectors menu Make a memo Chapter Network Viewer & Capture Parameter Determination Using the Network Capture functionLaunching the Network Viewer Control by the computer Internet PJ2 IntranetControl by the web browser Click Stop button to stop capturingRegistering the computers Control by the projectorAdvanced using example Setting conditionLaunch and quit the File Converter How to use the Network Viewer File ConverterCreate the available data File Converter Converting procedure Setting of conversion mode Other menu itemsConversion procedure Select a folder and click Save buttonProcedure of making program Making a program file Program EditorClick New button Enter a program name and click Add button Limitation of the Program file Using the Network Viewer function Condition to use the Network Viewer functionSelect input mode to Network previously Auto Display setting and control Click Register button to register a program Deletes the program Select input mode to Network previously Display the menu bar Network Viewer & Capture Chapter Controlling the Multi-Projectors Multi-Control Register IP address and projector name Check IP address and projector nameExclude/Add/Delete a projector StatusLoad and apply the setting value ControlControl multi-projectors at the same time Chapter Use of Serial Port Serial Port setting Connected to the serial portSerial port setting Control Examples ExampleInternet Use of Telnet PreparationFor example, entering pass- word Command list table Control the projector with TelnetConnection examples Web browser setting Technical data Chapter AppendixAExamples of Connection Peer-To-Peer connectionGateway Router installed in the network Meeting RoomProxy setting Web browser settingActive Script/JavaScript enable Windows XP Professional Internet Explorer ActiveScript settingExamples OS/Browsers Proxy setting Netscape Navigator JavaScript Setting 100 Product specification TCP/IPSerial port specification Port SpecificationLAN port specification FAQ FAQ How can I restrict access from the computer 105Password/Login What should I do when I forget the password? 106107 Why am I not receiving E-mail alert messages? Can I control the projector by using the telnet application?Can I update the firmware of the Network Unit 109What is the MAC address assigned to the Network Unit? What are the rules for IP address assignment?111 Cannot make a new program fileFile Converter What kind of image formats can I convert? 113
Top Page Image Contents