Sanyo PLC-XC56 owner manual Maintenance and Cleaning Lamp Replacement, Service Parts No 339

Page 64
Connect the AC power cord to the projector and turn on the projector.
Turn off the projector and disconnect the AC power cord. Allow the projector to cool for at least 45 minutes.
Loosen the screw with a screwdriver, slide and open the lamp cover.
Loosen 2 screws of the lamp with a screwdriver and pull out the lamp upwards vertically by grasping the handle.

Maintenance and Cleaning

Lamp Replacement

When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow. Replace the lamp with a new one promptly. The timing when the LAMP REPLACE indicator should light is depending on the lamp mode.

Note:

•When Mode 2 is selected in the Lamp life control menu, if the projection lamp of the projector reaches its end of life, the lamp replacement icon appears on the screen, and the projector is turned off automatically after 3 minutes.

•The Lamp replacement icon will not appear when the Display function is set to Off (p.46), during Freeze (p.25), or No show (p.26).

Top Control

Lamp replacement icon

LAMP REPLACE indicator

CAUTION

Allow a projector to cool for at least 45 minutes before you open the Lamp Cover. The inside of the projector can become very hot.

CAUTION

For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury.

CAUTION

When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get into your eyes or mouth, seek medical advice immediately.

Follow these steps to replace the lamp.

1

2

3

4 Replace the lamp with a new one and tighten the 2 screws back into position. Make sure that the lamp is set properly. Replace the lamp cover and tighten the screw.

5

6 Reset the lamp replacement counter..

See "Resetting the Lamp Counter" on the next page.

Lamp Cover

 

Screw

Screw

Handle

 

Screw

Lamp

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer.

●

Model No.. of your projector

: PLC-XC56

●

Replacement Lamp Type No.

: POA-LMP127

 

 

(Service Parts No. 610 339 8600)

64

Page 63 Page 65
Image 64
Page 63 Page 65
Contents Model PLC-XC56 Network SupportedFeatures and Design Table of Contents Safety Precaution To the OwnerSafety Instructions Air Circulation Safety InstructionsMoving the Projector AC Power Cord for the United Kingdom AC Power Cord for the United States and CanadaCompliance Part Names and Functions FrontBack BottomRear Terminal Part Names and Functions⑤ LAN Connection Terminal Top Control Remote Control ② Auto SET buttonRemote Control Operating Range Remote Control Battery InstallationRemote Control Code Adjustable Feet InstallationPositioning the Projector Connecting to a Computer InstallationCables used for connection Connecting to Video Equipment Connecting to Component Video Equipment Projector side AC outlet side Connecting the AC Power CordFor Continental Europe For the U..K Input signal guidance window Basic OperationTurning On the Projector Selected Input Source and Lamp ControlBasic Operation PIN Code Input Dialog BoxBasic Operation Turning Off the Projector Basic Operation How to Operate the On-Screen Menu Remote ControlTop Control On-Screen MenuBasic Operation Menu Bar For detailed functions of each menu, see Menu Tree on pagesAuto Setup Function Basic Operation Zoom and Focus AdjustmentKeystone Correction Basic Operation Sound Adjustment Volume Dialog BoxVolume Sound MenuBasic Operation Remote Control Operation Freeze buttonINFO.. button Zoom buttonsTimer button No Show buttonImage button Screen buttonInput Source Selection RGB Computer 1/Computer 2Analog Computer InputInput Menu Use the Point buttons to select Computer 2 Computer Input Computer System Selection PC System MenuComputer Input Auto PC Adjustment PC adjust MenuTo store adjustment parameters Auto PC adjComputer Input Manual PC Adjustment Reset Mode freeComputer Input StoreComputer Input Image Mode Selection Computer Input Image Adjustment Image Adjust MenuScreen Size Adjustment Screen MenuCustom Position H/VFor zooming in and out the images Digital zoom + Digital zoomVideo Input Input Source Selection Video, S-videoVideo Input MenuComponent RGB Scart Video Input Video System Selection AV System Menu Video or S-videoAV System Menu Component Or Computer 1Component and then pressImage select Menu Video Input Image Mode SelectionCinema Color Video Input Image AdjustmentTint Video Input Store MenuNoise reduction ProgressiveVideo Input Screen Size Adjustment Setting SettingSetting Menu LanguageAuto setup Auto setupInput search Auto KeystonePower off? p.20 TimerKeystone BackgroundLogo Logo and Logo PIN code lock settings DefaultLogo select LogoCapture Logo PIN code lockCapture Logo PIN code lockChange the Logo PIN code lock setting Change the Logo PIN code lock settingEnter a Logo PIN code Logo PIN code changeRear CeilingClosed Caption Power management Standby modeShut down On startLamp replacement icon Lamp controlLamp life control ModeRemote control To change the code for the remote controlFilter control  NoteKey lock SecuritySecurity Key lock and PIN code lock Key lockChange the PIN code lock setting Enter a PIN code Change the PIN codeEnter a PIN code Change PIN codeFilter counter FanLamp counter Filter counterFactory default Information Input Source Information DisplayMaintenance and Cleaning Indicator is blinking redIndicator lights red Projector is shut down and the Warning TempMaintenance and Cleaning Filter Instructions Filter replacement iconMaintenance and Cleaning Replacing the Filter Cartridge RecommendationResetting the Scroll Counter Maintenance and Cleaning Resetting the Filter CounterScroll counter Maintenance and Cleaning Cleaning the Lens Cover Cleaning the Projector CabinetMaintenance and Cleaning Lamp Replacement Service Parts No 339Lamp Handling Precautions Maintenance and Cleaning Resetting the Lamp CounterTroubleshooting AppendixAppendix Remote Control does Indicator blinks or lightsImage is distorted or runs off PIN code dialog box appearsAppendix Menu Tree Input Computer / VideoSound Computer InputVideo Input Setting InformationProjector is operating normally Appendix Indicators and Projector ConditionProjector is detecting abnormal condition Projector Condition Appendix Compatible Computer Specifications ON-SCREEN ResolutionSpecifications are subject to change without notice Appendix Technical Specifications Optional Parts Appendix PJ Link Notice Control Port Connector D-sub 9 pin Appendix Configurations of TerminalsTerminal Analog RGB Mini D-sub 15 pin PIN Code Lock No Appendix PIN Code Number MemoLogo PIN Code Lock No Appendix Dimensions KL5AC
Top Page Image Contents