Sanyo PDG-DSU20N, PDG-DSU20E, PDG-DSU20B owner manual Compliance, EN-5

Page 6

Compliance

Federal Communications Commission Notice

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

Model Number:

PDG-DSU20N

Trade Name:

Sanyo

Responsible party:

SANYO FISHER COMPANY

Address:

21605 Plummer Street, Chatsworth, California 91311

Telephone No.:

(818)998-7322

AC Power Cord Requirement

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada:

AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA).AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the

outlet, contact your electrician.

GROUND

 

AC Power Cord for the United Kingdom:

This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus ASA . If the fuse cover is detachable, never use the plug with the cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions.

If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.

The end of the flexible cord should be suitably prepared and the correct plug fitted.

WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET.

The Wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow .....Earth

Blue

Neutral

Brown

Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

WARNING: THIS APPARATUS MUST BE EARTHED.

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

EN-5

Image 6
Contents PDG-DSU20N/DSU20E/DSU20B Safety Precaution EN-1Voor de klanten in Nederland EN-2Notas acerca de pilas de Litio Solo CARIFORNIA, EE.UU Sanyo Fisher Sales Europe GmbHSafety Instructions EN-3Page Compliance EN-5EN-6 Contents Projector Features IntroductionEN-8 Package Contents Projector Overview Front ViewEN-10 Rear View Bottom ViewEN-11 Button Function Using the ProductControl Panel EN-12Connection Ports EN-13Remote Control EN-14Replacing the Battery EN-15Remote Control Operation EN-16Installation Connecting the ProjectorEN-17 Powering Off the Projector Powering On/Off the ProjectorPowering On the Projector EN-18Adjusting the Projector Zoom and Focus Adjusting the ProjectorAdjusting the Projector Height EN-19Adjusting Projection Image Size EN-20Menu Operation EN-21How to operate Picture Computer / Video ModeEN-22 Sound Computer / Video Mode Computer Image Computer ModeVideo Image Video Mode Setting Computer / Video ModeLanguage Computer / Video Mode Factory Default Computer / Video ModeEN-24 Cleaning the Projector Housing MaintenanceCleaning the Lens EN-25Replacing the Lamp EN-26Order Replacement Lamp EN-27Specifications Remote ControlEN-28 EN-29 LED Indicator MessagesAppendix Optional PartsVideo Compatibility ModesComputer EN-30Image problems TroubleshootingStart-up problems Remote control problemsPart No AA6P1P5486--KA7A a