Hitachi GR2000-B Series Normal Start-Up Process for the GR2000-B, Turning the Power Switch on

Page 33

Setup Process

2.9.5Turning the Power Switch ON

The power switch for the GR2000-B is a rocker switch located next to the power cord on rear panel. Operate the switch to turn power ON (1) or OFF (0). Turn on the power at the back of the GR2000-B.

ON

OFF

Power Switch

Figure 2-16 Switching Power ON and OFF

2.10Normal Start-Up Process for the GR2000-B

Below is the process from powering on the device to starting it.

1.The STATUS RMP indicator starts blinking green as soon as the system is powered ON.

2.The GR2000-B begins loading it’s software when the ACC (access) indicator lights in green. During this time, the STATUS RMP indicator continues to blink.

3.The STATUS RMP indicator lights solid green after the software has loaded. The system then starts up normally.

Note: The STATUS RMP or STATUS ETHERNET indicator showing red indicates

*trouble. For details, see the Hitachi Gigabit Router GR2000 Series Enhanced Version Operations Guide.

!

Caution: If a memory card is not installed, the GR2000-B stops running while showing

"20" in the STATUS CODE display. Power off the GR2000-B and install a

 

 

memory card, then power it on again.

 

 

 

2.10.1Turning the Power OFF

Turn the power switch at the back of the GR2000-B to OFF (0)

 

 

!

Caution:

While the access indicator (ACCESS) for a memory card is lit, the memory

 

 

 

card is being accessed. DO NOT pull out a memory card or turn off the

 

 

 

power switch while the memory card is being accessed. If so, you could

 

 

 

 

 

 

permanently damage the memory card.

 

 

 

 

Some commands require a long time to finish accessing a memory card

 

 

 

 

when they are executed. Make sure that the access to a memory card is

 

 

 

 

finished before pulling it out or turning off the power switch.

 

 

 

 

 

 

 

 

 

 

 

 

GR2K-GA-0008

2-13

Rev. 1.00

 

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Hitachi Gigabit Router GR2000-B Series Rev Hitachi Gigabit Router GR2000-B Series Quick Start GuideChange Record Release 1.00 AugustPreface GR2K-GA-0008Abbreviations GR2K-GA-0008 Rev IlmiLEC PIM Viii Safety Guide General Safety GuidelinesDamage to the equipment or a disruption in service Specific Warning Instructions Specific Caution Instructions Other Instructions CleaningStorage XiiTable of Contents Display of Operation Status XivDocumentation for the GR2000-B Series List of FiguresXvi List of Tables Xviii Documents about the GR2000-B models Chapter IntroductionDocumentation for the GR2000-B Series GR2K-GA-0008 Rev Chapter Setup Process Assemble the Required Tools for SetupCheck that All Necessary Components are Present GR2000-1B Setting Up the GR2000-B2 GR2000-2B Setup ProcessGR2000-2B Rear View GR2K-GA-0008 Rev Front panel indicators To yourself and the routerDue to static electricity Attaching the Rubber Feet Installing the GR2000-B on a Table or DeskConnecting a Power Cable to the GR2000-B Attaching and Detaching the Power CableInstalling a Memory Card Installing a Memory Card10 After Installation of a Memory Card Permanently damage the memory card SoftwareSetup Terminal Setup Terminal and Cable ConnectionsConnecting Cable Specifications Required for Setup TerminalsConnecting the GR2000-B to Other Devices Connecting a Setup Terminal to the GR2000-BTurning the Power OFF Turning the Power Switch onMemory card, then power it on again Normal Start-Up Process for the GR2000-BThis page left intentionally blank Chapter Basic Operations Configuration ExamplesSetting the Time First-Time LoginSet a password with passwd command Startup of the GR2000-BSetting the Configuration Enter the Administrator ModeBasic Operations Open the Configuration File Set a Default RouteSet an IP Address for the Ethernet Port Return to the Administrator Mode Close the Configuration FileManuals of the GR2000 Display of the Operation Status Covering the Entire Router Display of Operation StatusDisplay of the Operation Status of the Interface Configured Display of the Operation Status of the Built-In EthernetDisplay of the Routing Table More Details About Operation Details About Other SettingsThis page left intentionally blank Types of Trouble and Corrective Action Chapter TroubleshootingTroubleshooting and Reference manuals More Details About TroubleshootingTroubleshooting
Top Page Image Contents