Hitachi CP-S845W specifications Installation, Example of the projector and screen installation

Page 12

Installation

Example of the projector and screen installation

Determine picture size and projection distance as illustrated below.

View from the top

View from the side

Screen

Lens center

a

	Screen (inch)	a (inch)

		Minimum	Maximum
		Minimum	Maximum

	40	64	84

	60	97	127

	80	130	169

	100	163	213

	120	196	256

	150	244	319

	200	326
	200	326

a:Distance from the projector to the screen. (tolerance : ±10%)

This screen size is full-screen size.(800 dots X 600 dots)

Installation of liquid crystal projector

Please basically use liquid crystal projector at the horizontal position.

If you use liquid crystal projector by the lens up position, the lens down position and the side up position, this may cause the heat inside to build up and become the cause of damage.

Be especially careful not to install it with ventilation holes blocked.

How to use foot adjusters

Adjust the projection position using the foot adjusters at the bottom of the projector.

View from the front

View from the side

Foot adjuster

Vertical adjustments can be made in the range of 0 to 9°.

Horizontal inclination may be adjusted using the adjuster at the rear.

1.Lift up the projector and press the button of the adjuster to release the lock.

2.Adjust the projection angle, release the button of the adjuster and securely lock it.

3.To adjust the angle slightly, revolve the foot adjusters.

Caution

•Do not unlock the foot adjusters while you do not support the projector, to avoid falling of the projector and causing an injury.

•Do not revolve the foot adjusters by force, the foot adjusters is damaged.

•Securely lock the adjuster.

•Do not apply unnecessary force from the upper side when lifting the projector. Otherwise, projector may be damaged or a finger could be caught and cause injury.

12

Image 12

Contents Features ContentsOutline Operating GuideAbout Trademarks Video signal cables Power cordBefore use Instructions to UsersDo not look directly at the lens when Lamp is lit Do not install this unit in an unstable placeDo not use power supplies other Than that specified If any abnormality occursDo not stare directly into the laser aperture Class 2 Laser ProductCleaning Handle the power cord carefullyWhen you are not going to use for a Long time Clean inside the unit at least once two yearsDo not place this unit where it gets hot VolumeCleaning the lens Cleaning the cabinetContents of shipping box Names and functions of each partRemote control sensor Main Power switch AC in socketVideo input terminal RGB input terminalRemote control transmitter How to insert batteries Names and functions of each partInstallation Example of the projector and screen installationHow to use foot adjusters On indicator will light up orange Basic operationsTo project the picture For 3 secondsTo turn off the power Indicator lights up orangeStandby mode PLUG&PLAYFreeze Function Magnifying FunctionAdjustments and functions To return to the initial settingMemory function On-screen menus are displayed on the screenSET UP How to use the SET UP menuBar display items VOLUME, Bright etc Numerical display items V POSIT, H Posit etcAUTO-adjustment AUTO-adjustment Confirm ScreenDuring AUTO-adjustment Adjustment Item Details of adjustmentImage The menu Image serves of the picture inversion MirrorConnection to the video signal terminals Connection to the RGB signal terminalExample of computer signal Resolution Standard Display Dots KHzInitial set signals Computer/signal Horizontal Timing µsComputer/signal Vertical Timing lines Horizontal Timing µsConnection to the control signal terminal Control signal terminalPS/2 mouse ADB Mac mouseSerial mouse Control command table Control command tableCommunication RS232C cable OptionCommand data Procedure of getting the Projector status Procedure of setting the Projector statusProcedure of default setting the Projector status Example of command errorExample of system setup Connecting various equipmentAC Inlet Computer Note type ComputerDesk typeCleaning the air filter Air filter Filter coverDo not use with removed air filter Remove the lamp cover Loosen two screws and pull the handle to remove LampLoosen a screw and remove the cover Install the lamp cover and fix it using screws Reset the lamp timeLamp MalfunctioningIndicator display Message tableOn-screen display ActionWhen you think something wrong Dimension diagram Product name Liquid crystal projector Model name CP-S845WInput terminal Input/Output Terminal

Related manuals

Manual 34 pages 59.78 Kb