Hitachi CP-S845W Do not stare directly into the laser aperture, Class 2 Laser Product

Page 5

Warning

High temperatures are generated when the lamp is lit, so do not place objects in front of the lens.

Be careful in handling the power cord.

•Do not scratch, damage or process the power cord. Do not bend it forcibly. Also do not put a heavy object on it, do not heat it and do not pull it. If you do, the power cord may be damaged and it may cause a fire, electric shock, etc.

⋅Do not pull the cord.

⋅Do not put a heavy object on it.

⋅Do not damage the cord.

⋅Do not put it near a heating

device.

•Be careful that this unit is not placed

on the power cord. The power cord may be damaged and it may cause a fire, electric shock, etc. If the cord is covered with a carpet, etc. a heavy object may be put on it without your realizing it.

•If the cord is damaged (core wire is

exposed, disconnected, etc.), ask your dealer to replace it. It may cause a fire, electric shock, etc.

•Check that no dirt adheres to the

power plug and fully insert without any play. If dirt adheres or the connection is incomplete, it may cause a fire, electric shock, etc.

•The outer shield of power cord must be connected to ground.

If you do not, it may cause a electric shock.

ENGLISH

Do not stare directly into the laser aperture.

•The laser pointer on the remote control unit radiates the laser beam from the laser aperture.

•Do not stare into the laser aperture or radiate the laser beam to other persons as the laser emitted is a class 2 laser and it could damage you vision , etc.

Especially pay attention if children are present.

•The three labels below are caution labels for the laser beam.

LASER RADIATION

CAUTION

LASER RADIATION -

DO NOT STARE INTO BEAM

WAVE LEGTH : 670nm

MAX. OUTPUT : 1mW

CLASS 2 LASER PRODUCT

AVOIDE EXPOSURE-LASER

RADIATION IS EMITTED

FROM THIS APERTURE

RADIAZIONI LASER

NON GUARDARE NEL RAGGIO LUCE

APPARECCHIO LASER DI CLASS 2

RAYONNEMENT LASER

MANUFACTURED

NE PAS REGARDER DANS

 

LE FAISCEAU APPAREIL

Jun-99

A LASER DE CLASSE 2

 

LASER-STRAHLUNG

PLACE OF

NICHT IN DEN STRAHL

MANUFACTURER:

BLICKEN LASAER KLASSE 2

 

 

 

DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT WAVE LENGTH : 670nm MAX. OUTPUT : 1mW IEC60825-1 : 1993 + A1 : 1997

LASER APERTURE

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Contents FeaturesOutline Operating GuideAbout Trademarks Power cord Video signal cablesBefore use Instructions to UsersDo not install this unit in an unstable place Do not look directly at the lens when Lamp is litDo not use power supplies other Than that specified If any abnormality occursClass 2 Laser Product Do not stare directly into the laser apertureHandle the power cord carefully CleaningWhen you are not going to use for a Long time Clean inside the unit at least once two yearsVolume Do not place this unit where it gets hotCleaning the lens Cleaning the cabinetNames and functions of each part Contents of shipping boxAC in socket Remote control sensor Main Power switchVideo input terminal RGB input terminalRemote control transmitter Names and functions of each part How to insert batteriesHow to use foot adjusters InstallationExample of the projector and screen installation Basic operations On indicator will light up orangeTo project the picture For 3 secondsIndicator lights up orange To turn off the powerStandby mode PLUG&PLAYMagnifying Function Freeze FunctionTo return to the initial setting Adjustments and functionsMemory function On-screen menus are displayed on the screenHow to use the SET UP menu SET UPBar display items VOLUME, Bright etc Numerical display items V POSIT, H Posit etcAUTO-adjustment Confirm Screen AUTO-adjustmentDuring AUTO-adjustment Adjustment Item Details of adjustmentMirror Image The menu Image serves of the picture inversionConnection to the RGB signal terminal Connection to the video signal terminalsResolution Standard Display Dots KHz Example of computer signalComputer/signal Horizontal Timing µs Initial set signalsComputer/signal Vertical Timing lines Horizontal Timing µsControl signal terminal Connection to the control signal terminalSerial mouse PS/2 mouseADB Mac mouse Control command table Control command tableCommunication RS232C cable OptionCommand data Procedure of setting the Projector status Procedure of getting the Projector statusProcedure of default setting the Projector status Example of command errorConnecting various equipment Example of system setupAC Inlet Computer Note type ComputerDesk typeDo not use with removed air filter Cleaning the air filterAir filter Filter cover Loosen a screw and remove the cover Remove the lamp coverLoosen two screws and pull the handle to remove Lamp Reset the lamp time Install the lamp cover and fix it using screwsLamp MalfunctioningMessage table Indicator displayOn-screen display ActionWhen you think something wrong Product name Liquid crystal projector Model name CP-S845W Dimension diagramInput terminal Input/Output Terminal
Related manuals
Manual 34 pages 59.78 Kb
Top Page Image Contents