Hitachi CP-S845W Do not place this unit where it gets hot, Volume, Cleaning the lens

Page 7

Caution

Caution when replacing the lamp.

•When replacing the lamp, turn off the power of

the projector and disconnect the power plug from the power outlet. Then wait for

45 minutes to allow the lamp cool: Failure to do so could result in a burn.

• For disposal of used lamp, treat

 

according to the instruction of

Pull out the

power plug

community authorities.

from the

• Since the lamp is made of glass, do

power

not apply shock to it and do not

outlet.

scratch it.

 

• Also, do not use old lamp. This could also cause

 

explosion of the lamp.

 

• If it is probable that the lamp has exploded

 

(explosive sound is heard), disconnect the power

 

plug from the power outlet and ask your dealer

 

to replace lamp.

 

• In rare cases, the reflector and the inside of the

 

projector may be damaged by scattered broken

 

pieces of glass, and broken pieces could cause

Front glass

injury when being handled.

• When the lamp has been replaced, reset the

Reflector

accumulated operation time of the lamp.

Lamp

• Do not reset if the lamp has not been replaced.

 

ENGLISH

[General cautions]

Do not place this unit where it gets hot.

Be careful since if you place the unit outdoors, in a place exposed to direct sunlight or near a heating device, the cabinet and parts could be affected.

Volume.

Use at the proper volume level so that it does not bother persons in the neighborhood. Especially, since the sound is likely to carry well at the night even at a low volume, consider the neighborhood to a good living environment.

Cleaning the lens.

To clean the lens, use a generally-available lens cleaning tissue (used for cleaning lens of camera, glasses, etc.). Be careful not to scratch the lens with a hard object.

Cleaning the cabinet.

•Since many plastic materials are used on the surface of the cabinet, if the surface is cleaned using benzene, thinner, etc., it may change in quality or the coating may be peeled off. Avoid using chemicals.

•When a chemically-teated cloth is used, follow the cautions that come with the cloth.

•Do not spray a volatile agent such as insecticide on the unit. Do not leave a rubber or vinyl object touching the cabinet for a long time. It may cause the cabinet to change in quality or the coating to peel off.

•Clean the dirt from the cabinet and operation panel by dusting lightly with a soft cloth. If the dirt is conspicuous, wipe off with a cloth moistened with detergent diluted with water, then wipe off with a dry soft cloth.

Rest your eyes occasionally when viewing for a long time.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Operating Guide FeaturesContents OutlineAbout Trademarks Instructions to Users Video signal cablesPower cord Before useIf any abnormality occurs Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place Do not use power supplies other Than that specifiedClass 2 Laser Product Do not stare directly into the laser apertureClean inside the unit at least once two years CleaningHandle the power cord carefully When you are not going to use for a Long timeCleaning the cabinet Do not place this unit where it gets hotVolume Cleaning the lensNames and functions of each part Contents of shipping boxRGB input terminal Remote control sensor Main Power switchAC in socket Video input terminalRemote control transmitter Names and functions of each part How to insert batteriesExample of the projector and screen installation InstallationHow to use foot adjusters For 3 seconds On indicator will light up orangeBasic operations To project the picturePLUG&PLAY To turn off the powerIndicator lights up orange Standby modeMagnifying Function Freeze FunctionOn-screen menus are displayed on the screen Adjustments and functionsTo return to the initial setting Memory functionNumerical display items V POSIT, H Posit etc SET UPHow to use the SET UP menu Bar display items VOLUME, Bright etcAdjustment Item Details of adjustment AUTO-adjustmentAUTO-adjustment Confirm Screen During AUTO-adjustmentMirror Image The menu Image serves of the picture inversionConnection to the RGB signal terminal Connection to the video signal terminalsResolution Standard Display Dots KHz Example of computer signalHorizontal Timing µs Initial set signalsComputer/signal Horizontal Timing µs Computer/signal Vertical Timing linesControl signal terminal Connection to the control signal terminalADB Mac mouse PS/2 mouseSerial mouse RS232C cable Option Control command tableControl command table CommunicationCommand data Example of command error Procedure of getting the Projector statusProcedure of setting the Projector status Procedure of default setting the Projector statusComputerDesk type Example of system setupConnecting various equipment AC Inlet Computer Note typeAir filter Filter cover Cleaning the air filterDo not use with removed air filter Loosen two screws and pull the handle to remove Lamp Remove the lamp coverLoosen a screw and remove the cover Malfunctioning Install the lamp cover and fix it using screwsReset the lamp time LampAction Indicator displayMessage table On-screen displayWhen you think something wrong Terminal Dimension diagramProduct name Liquid crystal projector Model name CP-S845W Input terminal Input/Output
Related manuals
Manual 34 pages 59.78 Kb
Top Page Image Contents