Hitachi CP-S845W Lamp, Install the lamp cover and fix it using screws, Reset the lamp time

Page 31

Lamp (continued)

4	Replace the lamp with new one and
	fix it using the same two screws.	Screw
	• Firmly tighten the lamp screws. Loose screws may cause
	bad connection of the connector which in turn may result	Lamp
	in malfunctioning.	Lamp
	in malfunctioning.
5	Install the lamp cover and fix it using screws.
5	• To prevent burn, install the lamp cover and secure it using the screws.

• Do not turn on the power with lamp cover removed.

Lamp cover

Screw

•Whenever the lamp is replaced, reset the total operation time of the lamp. Do not reset if the lamp has not been replaced.

•Do not perform resetting without changing the lamp, as this can cause lamp breakage.

2. Reset the lamp time

If you have replaced the lamp after the lamp replacement time had expired, perform the procedure

explained below within 10 minutes after the power is turned on. The power will turn off automatically

when the 10-minute period expires.

	STANDBY/ON	MUTE
	FREEZE
	MAGNIFY VOLUME
	OFF
	POSITION ON	LASER
					STANDBY/ON
3					INPUT
3					MUTE
					MENU
	RESET	RIGHT			3
2	MENU ON	MOUSE ON			3
			1	1, 2	RESET
	BLANK	TIMER
	RGB	VIDEO

INPUT

ENGLISH

1)Press the RESET button on projector for 3 seconds or remote control TIMER button for 3 seconds and display the total lamp used time.

•When accumulated operation time of the lamp reaches 1500 hours, the following display will appear at the bottom of the screen.

2)Press the RESET button on projector or remote control MENU ON button during displaying the lamp used time.

3)Select the “0” on the screen using the MENU ( ) button or DISK PAD.

LAMP 1500 h

LAMP 1500		← 0		CANCEL

31

Image 31

Contents Operating Guide FeaturesContents OutlineAbout Trademarks Instructions to Users Video signal cablesPower cord Before useIf any abnormality occurs Do not look directly at the lens when Lamp is litDo not install this unit in an unstable place Do not use power supplies other Than that specifiedClass 2 Laser Product Do not stare directly into the laser apertureClean inside the unit at least once two years CleaningHandle the power cord carefully When you are not going to use for a Long timeCleaning the cabinet Do not place this unit where it gets hotVolume Cleaning the lensNames and functions of each part Contents of shipping boxRGB input terminal Remote control sensor Main Power switchAC in socket Video input terminalRemote control transmitter Names and functions of each part How to insert batteriesExample of the projector and screen installation InstallationHow to use foot adjusters For 3 seconds On indicator will light up orangeBasic operations To project the picturePLUG&PLAY To turn off the powerIndicator lights up orange Standby modeMagnifying Function Freeze FunctionOn-screen menus are displayed on the screen Adjustments and functionsTo return to the initial setting Memory functionNumerical display items V POSIT, H Posit etc SET UPHow to use the SET UP menu Bar display items VOLUME, Bright etcAdjustment Item Details of adjustment AUTO-adjustmentAUTO-adjustment Confirm Screen During AUTO-adjustmentMirror Image The menu Image serves of the picture inversionConnection to the RGB signal terminal Connection to the video signal terminalsResolution Standard Display Dots KHz Example of computer signalHorizontal Timing µs Initial set signalsComputer/signal Horizontal Timing µs Computer/signal Vertical Timing linesControl signal terminal Connection to the control signal terminalADB Mac mouse PS/2 mouseSerial mouse RS232C cable Option Control command tableControl command table CommunicationCommand data Example of command error Procedure of getting the Projector statusProcedure of setting the Projector status Procedure of default setting the Projector statusComputerDesk type Example of system setupConnecting various equipment AC Inlet Computer Note typeAir filter Filter cover Cleaning the air filterDo not use with removed air filter Loosen two screws and pull the handle to remove Lamp Remove the lamp coverLoosen a screw and remove the cover Malfunctioning Install the lamp cover and fix it using screwsReset the lamp time LampAction Indicator displayMessage table On-screen displayWhen you think something wrong Terminal Dimension diagramProduct name Liquid crystal projector Model name CP-S845W Input terminal Input/Output

Related manuals

Manual 34 pages 59.78 Kb