Hitachi ED-X12 user manual Remote control, Putting batteries

Page 15

Remote control

Remote control

Putting batteries

WARNING ŹAlways handle the batteries with care and use them only as directed. Battery may explode if mistreated. Do not recharge, disassemble or GLVSRVHRILQ¿UH

And also improper use may result in cracking or leakage, which could result in ¿UHLQMXU\DQGRUSROOXWLRQRIWKHVXUURXQGLQJHQYLURQPHQW

%HVXUHWRXVHRQO\WKHEDWWHULHVVSHFL¿HG'RQRWXVHEDWWHULHVRIGLIIHUHQW types at the same time. Do not mix a new battery with used one.

Make sure the plus and minus terminals are correctly aligned when loading a battery.

Keep a battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

Do not short circuit or solder a battery.

'RQRWDOORZDEDWWHU\LQD¿UHRUZDWHU.HHSEDWWHULHVLQDGDUNFRRODQGGU\SODFH

,I\RXREVHUYHDOHDNDJHRIDEDWWHU\ZLSHRXWWKHÀRZHUDQGWKHQUHSODFHDEDWWHU\

If the liquid adheres to your body or clothes, rinse well with water immediately.

Obey the local laws on disposing the battery.

1. Remove the battery cover.

Slide back and remove the battery cover in the direction of the arrow.

2. Insert the batteries.

Align and insert the two AA batteries according to their plus and minus terminals as indicated in the remote control.

3. Close the battery cover.

Replace the battery cover in the direction of the arrow and snap it back into place.

15

Image 15
Contents About this manual Thank you for purchasing this projectorTrademark acknowledgment Remote control ContentAbout this manual Content Projector features Setting upAbout contents of package Fastening the lens cover Part names ProjectorLamp and vents of the projector. Ì It could cause a burn CB/PB CR/PR Video portAudio OUT port Magnify Remote controlControl buttons Cursor buttons ŸźŻŹ STANDBY/ON buttonWKHDLU¿OWHU Setting upInch ArrangementScreen 16 9 screen Projection distance Screen heightElevator feet Elevator button Adjusting the projectors elevatorUsing the Security Bar How to attachSecurity Bar Anti-theft chain or wire sold separately About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting to a monitor outputExamples of connection with a VCR/DVD player CB/PBScart AC inlet Connector Power cord Connecting power supplyPutting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlSTANDBY/ON Power on/offTurning on the power Turning off the powerTemporarily muting the sound Adjusting the volumeSelecting an input signal OperatingSelecting an aspect ratio Searching an input signalAdjusting the zoom and focus Selecting an input signal€ For a component video signal Using the automatic adjustment featureAdjusting the position € For a video signal or s-video signalScreen to aid you in correcting the distortion. /#07#. Using the magnify featureWill be restored when the projector exits the Magnify mode Correcting the keystone distortionsTemporarily blanking the screen Freezing the screenMove pointer Available function Remote control operationOperating the computer screen USB mouse and keyboard controlAdvanced Menu Multifunctional settingsUsing the menu function Easy MenuEasy Menu Easy Menu 8VLQJWKHEXWWRQVŸźVZLWFKHVWKH*$00$PRGH Selecting a mode of Custom and thenAdjustment by pressing the Enter button Picture MenuOn the whole tones of the test pattern Picture MenuSelecting the Custom and then pressing Color TempLOAD1 Ù LOAD2 Ù LOAD3 Ù LOAD4 SAVE4 ÙSAVE3 Ù SAVE2 Ù SAVE1MY Memory Over Scan PhaseImage Menu Normal Ù 43 Ù 169 Ù SmallImage Menu For a video signal or s-video signalAuto Adjust For a component video signalInput Menu ProgressiveVideo NR RGB Input MenuVideo Format Frame LockResolution Downward, this function may not work correctly Setup MenuWhen the zoom adjustment is set to the Tele telephoto focus Function againAudio Setup MenuVolume Normal Ù Hinvert Ù Vinvert Ù+Screen Menu Menu PositionBlank Screen Menu Start UPMyScreen Lock No Input is Detected Sync is OUT of RangeMessage Option Menu Auto SearchAuto on MY Button Option MenuAuto OFF Lamp TimeHigh Ù Normal ServiceFactory Reset Ù Information Ù Remote Freq Enable Ù DisableRemote Freq 1NORMAL Ù 2HIGHInformation Security Using Security FeaturesInputting the Password Changing the PasswordSetting the Password Using the MyScreen Password FunctionDescription If you have forgotten your Password Turning on the MyScreen Password8VHWKHŸźEXWWRQVRQWKH6&85,7PHQX Using the PIN Lock FunctionTurning the Password off Registering the PIN CodeIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionUsing the Transition Detector Function Setting the Transition Detector PasswordTurning On the Transition Detector Function Inquiring Code will be displayed inside Setting the Transition Detector offPassword BOX large. The 10 digit Menu Select Turn OFF to display the EnterLamp MaintenanceTo lock it in place Case of replacement by yourselfLamp Type number = DT00757Handle Filter cover Type number = NJ22222Option menu $LU¿OWHUMark Caring for the lens Caring for the cabinet and remote controlOther care Inside of the projectorRelated messages TroubleshootingThere is no input signal Internal temperature is risingRegarding the indicator lamps Has become heated Regarding the indicator lampsCooling fan is not operating There is a possibility that the interior portionSignal source does not correctly work Electrical power cord is not pluggedPower switch is not set to the on position Signal cables are not correctly connectedColor Space setting is not suitable Volume is adjusted to an extremely low levelAudio setting is not correct Color settings are not correctly adjustedLamp is approaching the end of its product Lifetime Not properly adjustedEither the focus and/or horizontal phase settings are Whisper function is working6SHFL¿FDWLRQ Warranty and after-service249 mm 306 mm 86 mm 100 mm Example of computer signal Vesa TextVesa Initial set signals At RGB signal Connection to the portsPin CR/PR Component video CR/PR“9SSȍWHUPLQDWRU Component Video D Y, E CB/PB, F CR/PRCTS RTSConnecting the cable Communications settingRS-232C Communication Increasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset CommandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Frame Lock Mute Blank Remote Freq Greece