Hitachi ED-X12 user manual Power on/off, Turning on the power, Turning off the power, Standby/On

Page 17

Power on/off

Power on/off

WARNING ŹWhen the power is on, a strong light is emitted. Do not look into the lens of projector. Also do not peep at the inside of projector through a hole.

NOTE • Turn the power on/off in right order. Please power on the projector prior to the connected devices. Power off the projector later than the connected devices.

Turning on the power

STANDBY/ON

1. 0DNHVXUHWKDWWKHSRZHUFRUGLV¿UPO\DQG button correctly connected to the projector and the outlet.

2. Remove the lens cover, and set the power switch to the ON position.

The power indicator will light up in steady orange. Then wait several seconds because the buttons may not function for these several seconds.

(1)When AUTO ON in the OPTION menu is set to TURN ON:(40) The lamp will only be automatically turned on when the Power switch is turned on after the power was turned off by Power switch last time. Afterwards the POWER indicator

will begin blinking in green. When the power is completely on, the indicator will stop blinking and light in green.

POWER indicator

POWER

(Steady orange)

POWER

(2)When AUTO ON in the OPTION menu is set to TURN OFF please see step 3.

3.Press the STANDBY/ON button on the projector or the remote control.

To display the picture, select an input signal according to the section "Selecting an input signal" (18).

(Blinking in green)

POWER

(Steady green)

Turning off the power

Please pay special attention to below two points when you do:

(1)Please do not turn the projector on again for at least 10 minute in this case. Neglect could shorten the lifetime of the lamp.

(2)During use or immediately after use, do not touch around the lamp and vents of the projector (4 Ì) It could cause a burn.

1. Press the STANDBY/ON button on the projector or the remote control.

The message "Power off?" will appear on the screen for about 5 seconds.

2. Press the STANDBY/ON button on the projector or the remote control again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange.

Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER indicator will go

off. Attach the lens cover.

Power off?

POWER

(Blinking in orange)

POWER

(Steady orange)

17

Image 17

Contents Trademark acknowledgment About this manualThank you for purchasing this projector About this manual Content Projector features ContentSetting up Remote controlAbout contents of package Fastening the lens cover Lamp and vents of the projector. Ì It could cause a burn Part namesProjector Audio OUT port CB/PB CR/PRVideo port Control buttons Remote controlCursor buttons ŸźŻŹ STANDBY/ON button MagnifyWKHDLU¿OWHU Setting upScreen 16 9 screen ArrangementProjection distance Screen height InchElevator feet Elevator button Adjusting the projectors elevatorSecurity Bar Anti-theft chain or wire sold separately Using the Security BarHow to attach About Plug-and-Play capability Connecting your devicesExamples of connection with a computer Connecting to a monitor outputScart Examples of connection with a VCR/DVD playerCB/PB AC inlet Connector Power cord Connecting power supplyPutting batteries Remote controlChanging the signal setting for the projectors remote sensor Using the remote controlTurning on the power Power on/offTurning off the power STANDBY/ONSelecting an input signal Adjusting the volumeOperating Temporarily muting the soundAdjusting the zoom and focus Searching an input signalSelecting an input signal Selecting an aspect ratioAdjusting the position Using the automatic adjustment feature€ For a video signal or s-video signal € For a component video signalWill be restored when the projector exits the Magnify mode Using the magnify featureCorrecting the keystone distortions Screen to aid you in correcting the distortion. /#07#.Temporarily blanking the screen Freezing the screenOperating the computer screen Available function Remote control operationUSB mouse and keyboard control Move pointerUsing the menu function Multifunctional settingsEasy Menu Advanced MenuEasy Menu Easy Menu Adjustment by pressing the Enter button Selecting a mode of Custom and thenPicture Menu 8VLQJWKHEXWWRQVŸźVZLWFKHVWKH*$00$PRGHSelecting the Custom and then pressing Picture MenuColor Temp On the whole tones of the test patternMY Memory LOAD1 Ù LOAD2 Ù LOAD3 Ù LOAD4SAVE4 ÙSAVE3 Ù SAVE2 Ù SAVE1 Image Menu PhaseNormal Ù 43 Ù 169 Ù Small Over ScanAuto Adjust For a video signal or s-video signalFor a component video signal Image MenuVideo NR Input MenuProgressive Video Format Input MenuFrame Lock RGBResolution When the zoom adjustment is set to the Tele telephoto focus Setup MenuFunction again Downward, this function may not work correctlyVolume Setup MenuNormal Ù Hinvert Ù Vinvert Ù+ AudioBlank Screen MenuMenu Position MyScreen Lock Screen MenuStart UP Message No Input is DetectedSync is OUT of Range Auto on Option MenuAuto Search Auto OFF Option MenuLamp Time MY ButtonFactory Reset Ù Information Ù Remote Freq ServiceEnable Ù Disable High Ù NormalInformation Remote Freq1NORMAL Ù 2HIGH Inputting the Password Using Security FeaturesChanging the Password SecurityDescription If you have forgotten your Password Using the MyScreen Password FunctionTurning on the MyScreen Password Setting the PasswordTurning the Password off Using the PIN Lock FunctionRegistering the PIN Code 8VHWKHŸźEXWWRQVRQWKH6&85,7PHQXIf you have forgotten your PIN Code Turning Off the PIN Lock FunctionTurning On the Transition Detector Function Using the Transition Detector FunctionSetting the Transition Detector Password Password BOX large. The 10 digit Setting the Transition Detector offMenu Select Turn OFF to display the Enter Inquiring Code will be displayed insideLamp MaintenanceLamp Case of replacement by yourselfType number = DT00757 To lock it in placeHandle Filter cover Type number = NJ22222Mark Option menu$LU¿OWHU Other care Caring for the cabinet and remote controlInside of the projector Caring for the lensThere is no input signal TroubleshootingInternal temperature is rising Related messagesRegarding the indicator lamps Cooling fan is not operating Regarding the indicator lampsThere is a possibility that the interior portion Has become heatedPower switch is not set to the on position Electrical power cord is not pluggedSignal cables are not correctly connected Signal source does not correctly workAudio setting is not correct Volume is adjusted to an extremely low levelColor settings are not correctly adjusted Color Space setting is not suitableEither the focus and/or horizontal phase settings are Not properly adjustedWhisper function is working Lamp is approaching the end of its product Lifetime6SHFL¿FDWLRQ Warranty and after-service249 mm 306 mm 86 mm 100 mm Vesa Example of computer signalVesa Text Initial set signals Pin At RGB signalConnection to the ports CR/PR Component video CR/PR“9SSȍWHUPLQDWRU Component Video D Y, E CB/PB, F CR/PRCTS RTSRS-232C Communication Connecting the cableCommunications setting Changing the projector settings Set command Requesting projector status Get commandUsing the projector default settings Reset Command Increasing the projector setting value Increment commandRS-232C Communication Be EF FB FA Color Temp Gain G Aspect Frame Lock Mute Blank Remote Freq Greece