Hitachi 8000 Elite manual Installing Additional Drives, Guide Screw Device

Page 35

Installing Additional Drives

When installing additional drives, follow these guidelines:

The primary Serial ATA (SATA) hard drive must be connected to the dark blue SATA connector on the system board labeled SATA0.

Connect the first SATA optical drive to the white SATA connector on the system board labeled SATA1.

Connect devices in order of SATA0, SATA1, SATA2, then SATA3.

Connect an optional eSATA adapter cable to the black ESATA connector on the system board.

Connect a media card reader USB cable to the USB connector on the system board labeled MEDIA. If the media card reader has a 1394 port, connect the 1394 cable to the 1394 PCI card.

The system does not support Parallel ATA (PATA) optical drives or PATA hard drives.

You may install either a third-height or a half-height drive into a half-height bay.

You must install guide screws to ensure the drive will line up correctly in the drive cage and lock in place. HP has provided extra guide screws installed on the chassis. The hard drive uses 6-32 isolation mounting guide screws, eight of which are installed on the hard drive bracket under the access panel. All other drives use M3 metric screws, eight of which are installed on the optical drive bracket under the access panel. The HP-supplied metric guide screws are black. The HP-supplied 6-32 isolation mounting guide screws are silver and blue. If you are replacing the primary hard drive, you must remove the four silver and blue 6-32 isolation mounting guide screws from the old hard drive and install them in the new hard drive.

Figure 2-22Extra Guide Screw Locations

No.

Guide Screw

Device

 

 

 

1

Black M3 Metric Screws

5.25-inch Drives

 

 

 

2

Silver and Blue 6-32 Isolation Mounting Screws

3.5-inch Hard Drives

 

 

 

ENWW

Installing Additional Drives 29

Image 35
Contents Hardware Reference Guide Hardware Reference Guide About This Book Iv About This Book Table of contents Appendix D Electrostatic Discharge Standard Configuration Features Product Features1Front Panel Components Front Panel Components2Media Card Reader Components Media Card Reader Components3Rear Panel Components Rear Panel Components5Windows Logo Key Functions Using the Windows Logo KeyKeyboard 4Keyboard ComponentsArrow 6Serial Number and Product ID Location Serial Number LocationServiceability Features Hardware UpgradesSmart Cover FailSafe Key Unlocking the Smart Cover Lock1Removing the Smart Cover Lock Screws Removing the Computer Access Panel 3Replacing the Computer Access Panel Hardware Upgrades Replacing the Computer Access PanelRemoving the Front Bezel Removing Bezel Blanks 6Replacing the Front Bezel Replacing the Front BezelDDR3-SDRAM DIMMs Installing Additional MemoryDIMMs 1DIMM Socket Locations Populating Dimm SocketsInstalling DIMMs Enww 2Expansion Slot Locations Removing or Installing an Expansion Card11Removing an Expansion Slot Cover Enww Enww 3Drive Positions Drive PositionsRemoving a Drive from a Drive Bay 16Disconnecting the Optical Drive Cables17Disconnecting the Media Card Reader USB Cable Enww Enww Guide Screw Device Installing Additional Drives4System Board Drive Connections System Board Drive ConnectionsInstalling a 5.25-inch Drive into an External Drive Bay Enww 27Installing a Hard Drive into the Hard Drive Bay Removing and Replacing a Removable 3.5-inch Sata Hard Drive 30Removing the Thermal Sensor Enww Enww Enww Changing from a Minitower to a Desktop Configuration Enww Changing from a Desktop to a Minitower Configuration Enww Enww Table A-1Specifications SpecificationsPower Output Battery Replacement Type Enww HP/Kensington MicroSaver Security Cable Lock Installing a Security LockExternal Security Devices HP Business PC Security Lock PadlockEnww Figure C-6Engaging the Lock Front Bezel SecurityEnww Grounding Methods Electrostatic DischargePreventing Electrostatic Damage Computer Operating Guidelines and Routine Care Shipping Preparation Optical Drive PrecautionsCleaning SafetyIndex Enww