Electrical Safety, Handling Safety

2. Attention from the Safety Point of View

This section contains important instructions that should be followed during installation and maintenance of the NEC 500 and batteries. It is intended for customers who setup, install, relocate, or maintain APC equipment.

Electrical Safety

∙EMC verification is VCCI - A.

∙Do not work alone under hazardous conditions.

∙High short circuit current through conductive materials could cause severe burns.

∙A licensed electrician is required to install permanently wired equipment.

∙Check that the power cord(s), plug(s), and sockets are in good condition.

∙To reduce the risk of electric shock when grounding cannot be verified, disconnect the equipment from the AC power outlet before installing or connecting to other equipment. Reconnect the power cord only after all connections are made.

∙Do not handle any kind of metallic connector before the power has been removed.

∙Use one hand, whenever possible, to connect or disconnect signal cables to avoid a possible shock from touching two surfaces with different electrical grounds.

∙Connect the equipment to a three wire AC outlet (two poles plus ground). The receptacle must be connected to appropriate branch circuit/mains protection (fuse or circuit breaker). Connection to any other type of receptacle may result in a shock hazard.

CAUTION! Deenergizing Safety

∙If the equipment has an internal energy source (the battery), the output may be energized when the unit is not connected to an AC power outlet.

∙To deenergize pluggable equipment: first press the Off button for more than one second to switch the equipment off. Next disconnect the equipment from the AC power outlet. Finally, disconnect the battery.

∙To deenergize permanently wired equipment: set the power switch to standby . Next set the AC circuit breaker to standby . Then disconnect the batteries (including any expansion units). Finally, disconnect the AC power from the building power supply.

∙Pluggable equipment includes a protective earth conductor which carries the leakage current from the load devices (computer equipment). Total leakage current must not exceed 3.5 mA.

∙Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly effect its safety or effectiveness is not recommended.

WARNING! Battery Safety

∙This equipment contains potentially hazardous voltages. Do not attempt to disassemble the unit. The only exception is for equipment containing batteries. Battery replacement using the procedures below is permissible. Except for the battery, the unit contains no user serviceable parts. Repairs are performed only by factory trained service personnel.

Batteries must be recycled. Deliver the battery to an appropriate recycling facility or ship it to the supplier in the new battery’s packing material. See the new battery instructions for more information.

∙Do not dispose of batteries in a fire. The batteries may explode.

∙Do not open or mutilate batteries. They contain an electrolyte which is toxic and harmful to the skin and eyes.

∙To avoid personal injury due to energy hazard, remove wrist watches and jewelry such as rings when replacing the batteries. Use tools with insulated handles.

∙Replace batteries with the same number and type of batteries as originally installed in the equipment.

Handling Safety

⇒<18 kg (<40 lb.)

⇒ 32-55 kg (70-120 lb.)

⇒ 18-32 kg (40-70 lb.)

⇒ >55 kg (>120 lb.)

∙Be careful. Do not lift heavy loads without assistance.

∙Equipment with casters is built to move on a smooth surface without any obstacles.

∙Do not use a ramp inclined at more than 10°.

∙This equipment is intended for installation in a temperature-controlled (0° - 40° C) indoor area, free of conductive contaminants.

N8580-31 specifications

The NEC N8580-31 is a powerful and versatile telecommunications solution primarily designed for enterprise environments. This system stands out due to its robust architecture that supports diverse communication needs, making it an ideal choice for organizations looking to enhance their connectivity and operational efficiency.

One of the key features of the NEC N8580-31 is its high availability, ensuring continuous operation and minimal downtime. This is crucial for businesses that rely on uninterrupted communication to maintain productivity. The system is designed with redundancy in mind, incorporating backup power supplies and failover mechanisms to guarantee seamless service.

In terms of technology, the N8580-31 employs advanced VoIP (Voice over Internet Protocol) capabilities, enabling organizations to leverage their existing IP networks for voice communication. This feature not only reduces costs associated with traditional telephony but also enhances flexibility, allowing users to access communication tools from various devices and locations.

The NEC N8580-31 supports a wide range of telephony features, including call forwarding, voicemail, and conferencing. These features are complemented by sophisticated call management tools that enable organizations to monitor and analyze call traffic, ensuring efficient use of resources and improved customer service.

Another notable characteristic of the NEC N8580-31 is its scalability. As businesses grow, their communication needs often change. The N8580-31 can be easily expanded to accommodate additional users and features without significant upgrades or overhauls. This scalability is vital for businesses aiming to future-proof their investment in communication technologies.

The system also integrates seamlessly with various third-party applications and platforms, enhancing its functionality and enabling organizations to customize their communication solutions. This level of integration supports workflows and processes, allowing for improved collaboration among team members.

Moreover, the NEC N8580-31 prioritizes security, incorporating multiple layers of protection to safeguard sensitive communication and data. This is particularly important in today’s digital landscape, where data breaches and cyber threats are prevalent.

In summary, the NEC N8580-31 is a cutting-edge telecommunications solution that combines reliability, scalability, and advanced features. Its capabilities in VoIP, call management, and integration with other applications position it as a leading choice for enterprises seeking to enhance their communication systems while ensuring security and operational efficiency.