NEC 2000 IPS manual System Conditions/Limitations Peer-to-Peer IP

Page 278

Chapter 13 Voice Over IP (VoIP)

System Conditions/Limitations (Peer-to-Peer IP)

Limitations

Add-on-Module:

Dterm IP does not support Add-on Module feature.

Analog Port Adapters:

When the IPW-2U unit is attached with a Dterm Series E terminal, other optional adapters (except for ADA-U Unit) cannot be attached with the Dterm Series E terminal.

Back Ground Music (BGM):

Service features requiring continuous voice transmission such as Background Music feature cannot be used because the traffic may reduce overall performance of the Local Area Network (LAN).

Internal Zone Paging:

There is a maximum of three DtermIPs per Internal Zone Page Group. Internal All Zone Paging will not access IP Dterm.

Set Relocation:

Set Relocation is not available between Dterm IP terminals. This feature is for legacy terminals only.

Note: Legacy stations/trunks means the ones connected to the Time Division Switch (TDSW). Examples of legacy station/trunk cards are LC, DLC, COT, PRT, CCT, DTI, 8RST (DTMF receivers), CFTB (conference trunk), etc.

Conditions

DSS/BLF:

A DSS/BLF Console can be associated with the Dterm IP and can be used in a Remote PIM, but the DSS/BLF console must be connected to DLC card.

IP-PAD:

The IP-PADs are required for the following connections/statuses:

Connections between Dterm IP terminals and legacy stations/trunks Connections between Dterm IP terminals and IP trunks (H.323) Connections between legacy stations/trunks and IP trunks (H.323) Connections for CCIS networking via IP from/to legacy stations/trunks

While Dterm IP terminals are on hold (Consultation Hold, Call Transfer, Music-on-Hold, etc.) When any override service is activated (Executive Override, etc.)

Three/four-party conference including Dterm IP terminals

Page 13- 36	UNIVERGE NEAX 2000 IPS Request for Proposal (RFP) Reference Guide
	Issue 6

Image 278

Contents Univerge Neax 2000 IPS MayNEC Unified Solutions, Inc Liability DisclaimerInaset OAI Application Software Development ChapterIsdn Basic Rate Interface BRI Univerge Neax 2000 IPS Documentation List Introduction Overview of NECElectronic Age Invention AgeIndustrial Age Worldwide Leadership ComponentsInformation Age Global Resources CommunicationsSocial Contributions PeopleCommunity AssetsInnovation EducationNEC Unified Solutions, Inc Development ActivitiesDALLAS, TexasMajor Product AreasVertical Markets Competitive Benefits and AdvantagesIntroduction Introduction Univerge Neax 2000 IPS Ccis Connection MaintenanceStation to Station Connection PstnBuilt-in DRS Device Registration Server on MP Office Data Backup EnhancementVarious Installation Methods Reduced Hardware with IP based ArchitectureExtended Application Processor AP Port Capacity DC/DC Power Supply forUniversal Slot Dual MP SystemUniverge Neax IPS DML System Outline for Remote PIMCharacteristics of the Univerge Neax IPS DM/IPS DML/IPS DMR Advantages of Remote PIMPIM1 PIM2 PIM3 PIM4 PIM5 PIM6 PIM7 Stand Alone System CapacityIPS System Capacity Single MP System Capacity Per PIM IP PADIPS System Capacity Single MP System cont’d Capacity Per PIM IPS System Capacity Dual MP System Capacity Per PIM 2M-AMIIPS System Capacity Dual MP System, Cont’d Capacity Per PIM IP-PAD IPS DM/IPS DML System CapacityCapacity Per MC 8LCBuilt-in Router Max card per Site Dtmf Sender Capacity IP Remote Network CapacityTotal System Capacity Main plus Remote IPS Pimmj As Remote PIM Capacity IPS DMR CapacityDTI Isdn Hardware Architecture Voice and Data SwitchingSystem Architecture Main Processor MP with Integrated Functionality Hardware DesignFusion of RAM and ROM Programs Application ProcessorsSN716 Attendant Console IntegrationUnified Circuit Card Analog/Digital TelephonesUniverge Neax 2000 IPS System Configuration PIMDual MP System Module and Installation HardwareSingle MP System ModulesAbbrev Description Quantity Installation HardwareInstallation Hardware Battery Backup Name Code Qty RemarksCabling Internal CablingMaintenance Administration Terminal MAT RS-232C External CablingSMDR/PMS/Hotel Printer/MCI with AP00B MRC-C External Alarm DisplayBuilt-in SMDR/MCI on MP Cable for AP00 Name Code Qty RemarksUniverge Neax IPS DM/IPS DML/IPS DMR System Configuration IPS DM/IPS DML Modular Chassis MCIPS DMR Modular Chassis MC Modular Chassis 2 Modular ChassisModular Chassis MC Installation Modular Chassis MC and BracketSystem Power Supply and Cooling Fan PKG IPS Software ArchitectureSystem Packages Univ IPS DM IP SYS PKG-E DM to Univ DM Upgrade KitUniv IPS DML IP SYS PKG Univ IPS DM/DML Expansion Module 1EUniv IPS DMR SYS PKG-E IP Remote PIM PackagesDescription Remarks Univ IP Remote PIM-B IPSKey Keeper Parent Capacity Option Software Keys/LicensesDescription Remarks Generic Program Capacity Option used w/Key KeeperMain Processor MP System HighlightsProcessors Name Code RemarksDAT Firmware Processor FPPN-CP24-C PN-CP31-C PN-CP27-A AP Card Application Processor APApplication Processor AP Cards FunctionMean Time Between Failures Mtbf Reliability and Availability Chart Description FitReliability and Availability Mtbf MttrReliability and Availability Chart Reliability Description Availability FitReliability Description Availability FitYears Availability Calculations Mean Time To Repair MttrReliability Calculations Reliability CalculationBusy Hour System TrafficTraffic Load Bhca Busy Hour Call AttemptsCalculation Procedure Traffic Capacity In Erlang For TDM CircuitsTraffic Capacity per Line For TDM Circuits Number of TrunksCOT Erlang B TableTraffic Internal Call Distribution External Line Trunk Trunk PEG Count Wireless PEG CountPEG Count UCD PEG CountVoIP H.323 Number of Voice Channels per IP TrunkCcis Point-to-Multipoint Payload size for Virtual IPTIP PAD Calculation IP PAD Calculation Number of extensions 100IP PAD Calculation Number of extensions 120 200 208 264 300 320 376 432System Specifications Loop Resistance including Opposite End Resistance Transmission Characteristics For TDM CircuitsLine Conditions Cable LengthDtmf Signal Rotary Dial Pulse and Dtmf SignalingRotary Dial Signal Description Specifications Receiving SendingMulti-frequency Compelled MFC R2 Signal Dimension and Weight Audible Tones and Ringing SignalRinging Signal Audible Tones Frequency InterruptionEMC Univerge Neax IPS DM/IPS DML/IPS DMR System SpecificationsSystem Specifications Open Industry Standards10BASE-T/100BASE-TX IP SpecificationsFAX LAN interface transmission modes RemarksHipaa Compliance System ComplianceHipaa Summary Department of Defense CompliancePage Equipment Name Function Name Module/Installation HardwareEquipment List Equipment Name Remarks Circuit Cards Common Control CardsEther PN-CP31PN-CP15 PN-PW00 ExtpwrFunction Name Port Remarks Application Processor CardsApplication Processor Card Name and Function Application Processor Cards SPN-AP00B DBM-C AP QsigLine/Trunk LT Cards Line/Trunk LT CardsDeskcon SPN-2ILCAPN-8DLCL PN-4DLCMPZ-24IPLA PAD-EPAD-C SPN-16VCTAA IPPN-4COTG PN-8COTQPN-4COTB PN-2ODTASPN-IPTB-A PN-2DATAPN-TNTA SPN-4VCTI-ASPN-4CSIA PN-RTAPage Dterm Series i Terminals Station EquipmentTerminal Line Up Dterm Series E TerminalsDterm IP Soft Phones Wireless HandsetInaset Dterm ExtendersDescriptions of the Dterm IP Terminals Specification for Analog TerminalsPhysical Features Call Handling Features Convergence FeaturesDTR-16LD-1 BK TEL DTR-16LD-1 WH TEL Descriptions of TerminalsDTR-2DT-1 BK TEL DTR-2DT-1 WH TEL DTR-4D-1BK TEL DCR-60-1 BK Console DCR-60-1 WH ConsoleStandard features SpecificationTerminal Options Cable Length Standard With AC AdapterStandard features Dterm Series E Soft keysDescriptions of Series E Multi-line Digital Terminals Description of Series E Multi-line Digital Terminals HFU-U Dterm Series E Accessories & AdaptersADA-U APR-UWMU-W ACA-UWMU-U IPW-2U ELC16D 32D Add-On Dterm Series E Specifications2DT DSSDterm Series E Line Conditions Loop Resistance and Distance Long Loop circuit built-inOptions Dterm Cordless TerminalsDterm Cordless II DTR-4R-2 BK Dterm Cordless Lite II DTH-4R-1 BK OptionsSpecifications Plantronics CT CordlessInaset Applications Additional ApplicationsPBX System Requirements Inaset Terminal Line UPInaset Basic Network Capability WM-RL UnitDterm PS III Wireless Handset Dterm PS III OptionsKey Features and Benefits FeaturesReal Time Communication Links with PC applicationsInternet Link Presence/StatusVoice Recording Application CollaborationCall Log Export Voice Quality AlarmOne Key Operation Line DisplayPB tone sending Client PC specificationOne Touch Button in Compact Mode Pause into Dialing stringSoftware/Licenses/Accessories PBX Specification Must be peer to peer IP enabledDterm SP30 Softphone Parts List Dterm ExtendersService Conditions for Dterm Analog EXT Page Type of Trunk Circuit Package TrunkingType of Trunks LT/APTrunk Card Specifications Trunk ParametersPN-AUCA SPN-BRTC PN-4RSTC ID Number Receiver PN-8RSTG Dtmf ReceiverPN-4RSTBA MF Receiver for T1 MF ANI PN-4RSTBA-911 MF SenderSystem Trunking Capacity IPS Trunking Capacity System CapacityIPS DM/DML Trunk Capacity Route Restriction Class RSC Least Cost Routing LCRSix Digit Least Cost Routing Priority Restriction Class Toll RestrictionDigit Toll Restriction Page Attendant Answering Position Attendant Console SN716Deskcon Exclusive Features SN716 Deskcon General FeaturesSN716 Deskcon Exclusive Features Face Layout of the SN716 Deskcon Functions and use of Keys and Lamp Indications Location Key or Lamp Full Basic Key/Lamp Number DesignationLDN LCD SN716 Specifications Interface ’ty Remarks Power OptionsBusiness Attendant System BAS BAS Benefits Business Attendant System Directory Business Attendant System Additional Features Business Attendant System Speed Dials PadBusiness Attendant System Ccis Network Information Business Application Environment Hardware RequirementsPage Customer Administration Terminal CAT System AdministrationSystem Administration Password EntryMaintenance Administration Terminal MAT PBX Configuration Wizard Mach Script EditorMinimum Requirements Recommended Traffic ManagementMATWorX PC Requirements Remote Maintenance System DiagnosticsSelf Diagnostic/System Messages Service ConditionsMP Download Process General Service ConditionsMP Program Download Required Hardware Program Download Service ConditionsProgram Changeover Service Conditions Equipment CommentsMA4000 Management System Feature Descriptions Business/Hotel/Data Feature ListBusiness/Hotel/Data Feature List Descriptions Snmp Business/Hotel/Data Feature Descriptions Attendant Console SN716 Deskcon Attendant Assisted CallingAttendant Camp-on Full and Semi- automatic Attendant Lamp Check Attendant Lockout Attendant Delay AnnouncementAuthorization Code Attendant OverflowAutomatic Call Distribution ACD Automatic Camp-onBackground Music Automatic RecallAutomatic Wake-up Back Up CPUCall Forwarding Brokers CallCall Back Call Park Call Transfer Call PickupCall Redirect Caller ID ClassCentrex Compatibility Class of ServiceCamp-on Check In / Check OutGroup Call Conference Six/Ten PartyConference 32 Party Consecutive Speed DialingData Line Security Delayed RingingDiagnostics Dial By NameDirect Outward Dialing DOD Direct Inward System Access DisaDirect Inward Termination DIT Direct Station Selection/Busy Lamp Field DSS/BLF ConsoleDo Not Disturb Distinctive RingingDterm Assistant Elapsed Call TimerFax Arrival Indicator DtermIPFlexible Numbering Plan Feature Activation from Secondary ExtensionFlexible Line Key Assignment Forced Account CodeHands-free Dialing and Monitoring Individual Attendant AccessHands-free Answerback HoldLast Number Redial IP Enabled DtermInternal Zone Paging with Meet-Me Least Cost Routing 3/6 DigitMessage Registration Miscellaneous Trunk AccessMessage Center Interface MCI Message ReminderModem over IP Mobility AccessNight Service MP Program Download FTPOff-Premises Extensions Off-hook AlarmNo CID Call Routing Optical Interface Pooled Line AccessPower Failure Transfer Pad LockAutomatic Idle Return Remote PIM over IP Reserve PowerRemote Hold Resident System ProgramSave and Repeat Security AlarmSingle Digit Feature Access Codes Set RelocationTerminal Login via NAT System Clock Setup by Station DialingTenant Service Tie Line Tandem SwitchingTrunk Direct Appearances Timed Queue Uniform Call Distribution UCDTimed Reminder Trunk Queuing OutgoingVariable Timing Parameters Voice Mail Private PasswordUniform Numbering Plan UNP -Voice and Data Voice GuideVoIP Log Collection Voice Mail TransferVoice Over IP H.323 WhisperCcis Feature List Ccis Features Descriptions Call Forwarding Intercept Ccis Centralized E911 Ccis Flexible Numbering of Stations Ccis Multiple Call Forwarding All Calls Ccis Station-to-Station Calling Ccis Isdn Feature List Isdn Feature Descriptions Event-Based Ccis SIG Feature List SIG Feature DescriptionsWireless Feature List Interface Wired for Wireless Table of Features by Configuration TypeFeature Adjunct Type Integrated Type Analog PBX Ccis Univerge Neax 2000 IPSWireless Feature Descriptions Group Call 2Way Calling This feature protects a call from being tapped Page 2400 Extended Format System Input/Output I/O InterfacesStation Message Detail Recording Smdr Smdr w/AP00 IMS FormatSmdr Terminal Interface Pattern D Combinations between Smdr and Smdr Output FormatCombinations available at the same time ARP, IP, ICMP, UDP, TCPCombinations for Center Office of Centralized Billing Combinations for Local Office of Centralized BillingData Transmission Sequence for Ethernet Interface System CapacityDescription Qty Remarks Message Center Interface MCIHardware Required for Smdr Modem Hardware Required for MCIVMS Property Management System PMS FeatureFeature Type of InformationPMS Interface RS PRT-4S CA-A Hardware Required for PMSDescription Qty Remarks OpenWorX Attendant Statistics Open Application InterfaceSystem Outline OpenWorX Business Attendant System BASBAS Call Control Functionality Brief Definition of Queues Brief Description of Call Control FunctionDid for Company Lookup BAS Speed Dials PadBAS Directory BAS Overhead Paging BAS Offline Mode Pseudo Night ModeBAS Authorization and Account Code Dialing BAS Call Recording and PlaybackBR Directory OpenWorX Business Receptionist BRBR Speed Dials Pad BR Overhead PagingBR Attendant PC Minimum Hardware Requirements BR Authorization and Account Code DialingOpenWorX Communications Portal Communications Portal Functionality Communications Portal BenefitsDialer Benefits OpenWorX DialerDialer Database OpenWorX Location Status Information LSI OpenWorX Message Reader MRSTM Benefits OpenWorX Short Text MessagingMR Benefits ICA Benefits OpenWorX Incoming Call Assistant ICAICA Functionality ICA ICA vs. Camp On OpenWorX Group Call Forward Control GcfcICA Comparison of ICA and IPS Functionality OpenWorX Personal Call Assistant PCA Gcfc FunctionalityDesktop Directory PCA Limiting User ViewsPCA OpenWorX Desktop Personal DirectoryOpenWorX Name Display PCA OpenWorX InasetBAS Ccis Network Information OpenWorX Multiple Ccis Node ConfigurationOAI Application Software Development Business Receptionist Ccis Network InformationPage Basic ACD Automatic Call Distribution ACD with MISAutomatic Call Distribution ACD Busy In/Busy Out ACD Basic ACD FeaturesDelay Announcement ACD Call Waiting Indication ACDPriority Queuing ACD CallCenterWorX ACD 3.0 for BusinessImmediate Overflow ACD Queue Size Control-ACDCallCenterWorX ACD Features Automatic Call Distribution with MIS Business Software Only Packages CallCenterWorX MISBusiness Turnkey Packages CallCenterWorX ACD 3.0 for Business Turnkey PackagesCallCenterWorX MIS 5GB Business System CapacitiesItem ACD Capacities CallCenter WorX MIS BhcaACD Terminals PBX RequirementsRelated Documents PBX Requirements RemarksContact Routing Q-Control Master Contact Center SolutionsMaster Reports Q-Control Announcements Q-AnnounceAgent Desktop Q-Desktop Callbacks Q-Callback Multi-Media Q-Email, Q-Chat, Q-FaxOutbound Dialing Q-Outdial Interactive Voice Response Q-IVRAuto Attendant QueWorX 4.0 FeaturesQueWorX 4.0 Licensed Applications Internet Initiated Callbacks Immediate Customer CallbackScheduled Callbacks Estimated Time to Answer ETAMultilingual Announcements Screen PopSoft Phone Global Repeat VerificationCustomizable Reports Professional Services for QueWorXCustomized Announcements VoIP Solutions VoIP SolutionsExtended Enterprise IP Solution Voice over IP VoIPTypical IP Gateway, Branch and Adapter configurations Equipment Name FunctionIP Station Peer-to Peer Connections between IP Enabled Dterm Peer-to-Peer Connections over Ccis Networking via IPConnections to Legacy Stations and Trunks Remote Connections of IP StationsAutomatic Program Download for IP Enabled Dterm 8IPLA/24IPLA Options Per Location Service Conditions on Legacy Service Features Service Conditions on System RegistrationMD5 is an algorithm defined in RFC 1321 from the Ietf Service Conditions on Encryption in System RegistrationService Conditions on Vlan Service Conditions on Remote Connections Local Connection Mode Remote Connection ModeExample 1 When Sta logs in Location #1 Location number in each operation mode for each IP stationOperation mode for each IP terminal Example 2 When Sta logs in Location #2Service Conditions on Automatic Program Download SPN-32IPLAA IP PAD Ccis Networking via IPRequired Equipment for IP Station SPN-16VCTAA IP PADCcis Networking via IP Peer-to-Peer Connections Basis IP Trunk Point-to-Multipoint Connection Ccis Networking via IP Non Peer-to-Peer Connections BasisPoint-to-Multipoint Connection Required Equipment for IP Ccis via IP Trunk cards Service Conditions IP Ccis via IP Trunk cardsIP Trunk Card Specifications Payload Period Maximum Voice Channels per IP TrunkConnection Service Conditions for H.323 FeaturesFeatures IP Trunk Specifications Required Equipment for H.323FAX and Modem over IP Example of FAX and Modem over IP connectionSPN-8IPLA IP PAD-A SPN-8IPLA IP PAD-CSPN-8IPLA IP PAD-B SPN-32IPLA IP PAD-EOpposite Office Required Equipment for FAX or Modem over IPOpposite Office 2000 IPS OwnConnection Conditions Required Bandwidth One-way Required bandwidth for FAX ConnectionRequired bandwidth for Modem Connection Requirement Remarks Remote PIM over IPNetwork Conditions and Payload Compression Bandwidth RequirementWith G7.23.1 With G729a 8k Without Compression 3k/6.3k Advantages Remote Site Equipment Name Remarks Required Hardware and SoftwareHost Site Equipment Name Remarks List of Service Features Operation XNoteVoice Messaging Planning and InstallationVendor Support for Open System Standards Bandwidth requirementsNetwork Consideration Network BandwidthCodec Total Bandwidth per transmit stream Msec Bandwidth utilizationCodec Filler Time Msec Quality of Service QoS Device Registration Server DRS and DhcpFor Voice Control/Voice Packet Port Type Destination Default Port No RemarksFor Dterm IP IPT Ccis For Ccis Virtual IPTFor H.323 IP Trunk PBX TCPConditions System Conditions/Limitations Peer-to-Peer IPLimitations Common Channel Inter-Office Signaling Ccis System Outline of a Ccis Connection Ccis and Isdn Analog Ccis Digital and Analog CcisDigital Ccis Peer-to-Peer Connections Voice CompressionCommon Channel Inter-Office Signaling Ccis Service Conditions on Non Peer-to-Peer Connections Ccis Networking via IP Non Peer-to-PeerCenter office Centralized BillingLocal office/Tandem office Common Channel Inter-Office Signaling Ccis Centralized E911 Ccis Call Set Up Times Look Ahead RoutingShared Trunk Facilities and Alternate Routing Alternate RoutingCentralized Management Center Centralized System Maintenance and AdministrationCentralized Maintenance Facility Centralized Call Accounting/Billing Systems Centralized Call Accounting / BillingCcis Centralized Voice Mail Centralized Voice Processing / MessagingCentralized Attendant Consoles Uniform Numbering Plans Ccis Feature ChartCcis Feature Name Neax 2400 Required YESCcis Feature Chart System Capacity for Ccis with Analog Interface System CapacitySystem Capacity for Ccis with Digital Interface System Capacity for Ccis Networking via IPRequired Equipment for Analog Ccis Required EquipmentRequired Equipment for Digital Ccis Required Equipment for Ccis Networking via IPPAD IP SpecificationsSpecifications Remarks 24IPLADTI Specifications Characteristics ChannelPage Isdn Feature List Integrated Services Data Network IsdnPRI Services & Features Isdn Primary Rate InterfaceCPN To Network-Present Call-By-Call Service SelectionCalled Party Recognition Service Direct-In Termination DIT CPN To Terminating User-Display Isdn Terminal Did AddressingDid and DOD Addressing AT&TPage Multiquest /900 Service Megacom Access/WATSMegacom 800 Service/800 Wats Ultra Wats Subaddress-PresentTrunk Provisioning Service Selection Event Based CcisBusiness Feature List Business Feature ListSupported Network Services Trunk provisioned only Isdn Network Requirements for Layer OneFor 30DTI Isdn PRI SpecificationsFor 24DTI For 24PRTBRT NET IPS Dedicated Access AT&T NTI MCI SprintDMS Selection 4ESS NET DMS Provisioning 4ESS NETVoice Features DMS 4ESS NET AT&T NTI MCI SprintAT&T MCI Sprint Provisioning DMS 4ESS NET IPS Switched Data AT&T MCI Sprint Selection DMS 4ESS NET IPS Switched DataDedicated Access NTI AT&T MCI Sprint Virtual Private Network DMS 4ESS NETDedicated Access AT&T NTI Siemens Services and Features LEC CarriersCall by Call Service AT&T NTI Siemens Selection 5ESS Virtual Private Network AT&T NTI DMS 4ESS NETFacility Management Voice Features AT&T NTI SiemensAT&T NTI Siemens Network Message WaitingAT&T NTI Siemens 5ESS Call By Call Service SelectionEwsd Switched Data Virtual Private Network AT&T NTI SiemensIsdn Basic Rate Interface BRI ApplicationsSystem Requirements ONE SC03 Supports Four 2ILCAIsdn BRI Required Equipment Isdn Equipment ListIsdn PRI Required Equipment Isdn Terminal Required EquipmentSystem Capacity for ISDN-BRI DocumentationCapacity for ISDN-PRI 24DTI 24PRTPage Wired for Wireless Wireless SystemUniverge Neax 2000 IPS Wireless Communication System WCS Analog PBX InterfaceCcis Interface Wireless Roaming Multi-Site Roaming 931a Roaming over IP Trunk Wireless Definitions HLRWireless Short Text Message Notification OAI Configuration Application Integrated Type2000 IPS Interface1 Interface2 Wired for Wireless FeaturesFeature Matrix by Configuration Type Adjunct Type Integrated TypeFeature Descriptions Way Calling Wired forWireless HandoverOut of Zone AuthorizationPreset Dialing IndicationSystem Description Dterm PSBattery Charger Dterm PS III AccessoriesLithium-Ion Battery HeadsetsZone Transceiver II ZT Integrated Adjunct Analog Adjunct Ccis Wireless SpecificationsZone Transceiver II Specifications WCS Required Equipment Equipment Description QTY RemarksPN-IPTB IPT PN-4VCTI 4VCTWireless LAN Documentation Wireless LANWireless LAN Handset PMS Hotel Feature ListHotel/Motel System Terminal ConsoleHotel/Motel Front Desk Terminal Application ProcessorHotel Console Station Message Detail Recording SmdrHotel Printer Executed Task Print OutAutomatic Wake-up Do Not Disturb Console Check In / Check OutDirect Data Entry CheckHotel/Motel Attendant Console Do Not Disturb-Hotel/MotelDo Not Disturb-System Hotel/Motel Front Desk Instrument House Phone Maid StatusVoice Message Waiting System Message RegistrationMessage Waiting Voice Message Waiting IndividualProperty Management System PMS Room Cutoff Room Cutoff ConsoleItems indicated are as follows Room StatusSingle Digit Dialing Description Capacity Specifications PMS/SMDR Interface Hotel Printer InterfaceHotel System Capacity Station Equipment SN716 DeskconCall Accounting AIMWorXSelect Database Licensing Option Description Multi-Site Centralized OperationsAIMWorX databases Oracle database Information you need before installing AIMWorXSQL Server licensing LicensingCall Record and User Capacity ConfigurationsStandalone Corporate tier AIMWorX ManagerIntegrating AIMWorX modules Enterprise tierAsset Manager Alarm Manager1 SPE Auth Code ManagerCustom SPE Writer Bill ReconcilerCable Manager Hospitality LinksVoice Mail SPE Additional Reference MaterialTrouble Ticket Work OrderVoice Messaging Systems Voice Mail IntegrationVoice Messaging Systems Description MCI Service Conditions NEAXMail AD-120 System ArchitectureVoice Cards Level II Server Software License with ExchangePlatform Components Client Access Licenses CALThird Party Software Third Party Fax Server Integration Optional Software Feature PackagesMail Reader Text-to-Speech PBX Integration SoftwarePlatform Specifications 2GBNEAXMail AD-64 Level I Dell GX280 Level II Dell PE2800 Level I/Level II Platform SpecificationsLevel I/Level II Specifications Platform Level 40GB Sata 36GB ScsiOptional Software UPS Uninterruptible Power SupplyAdditional Hardware Components Optional ActiveFax SoftwareUnified Messaging Hacker Prevention Features are as follows Voice Messaging Systems Voice Messaging Systems Automated Attendant Available LanguagesAudiotext Mailbox ManagerVoice Messaging Systems Maintenance Voice Messaging Systems Visual Messaging ViewMailViewCall Plus Full Digital Integration NEAXMail IM-16 LXUnified Messaging and Call Management Enjoy the Benefits of Integrated Messaging Hospitality Feature PackageBasic Features Additional Features Univerge Neax 2000 IPS Documentation List Niverge Neax 2000 IPS Features and SpecificationSystem Documentation Univerge Neax 2000 IPS Technical Manuals

Related manuals

Manual 59 pages 49.46 Kb