NEC NEAX2000 IVS2 system manual DTI Assignment, Startdescription Data

Page 40

CHAPTER 3 SYSTEM DATA PROGRAMMING

DTI Assignment

DTI ASSIGNMENT

STARTDESCRIPTION

DATA

CM05

CM07

CM20

Assign an AP number to the DTI card. The AP number must match the SENS switch setting on the DTI card.

INITIAL

Assign a Q-SIG trunk number to each channel number on the DTI card.

INITIAL

The system allocates time slots to consecutive channels from lowest to highest channel number assigned. To minimize the number of time slots allocated, assign trunk numbers to the consecutive channels on each card. Never skip channels in CM07.

Assign the access code for Q-SIG to LCR Group 0-3.

Y=0

(1)04-15, 20-31: AP No.

(2)09: DTI card

YY=01

(1) XX ZZ

XX:04-15, 20-31: AP No. assigned by CM05 Y=0

ZZ:01-15, 17-31: Channel No. of DTI

NOTE 1

(2)D000-D255: Trunk No.

Trunk No. already assigned by CM10 cannot be used.

Y=0-3 Numbering Plan Group 0-3

(1) X-XXXX: Access code

(2) A126-A129: LCR Group 0-3

A

NEAX2000 IVS2 Q-SIG System Manual

Page 33

ND-70923 (E), Issue 1.0

Image 40
Contents SIG System Manual Liability Disclaimer NEAX2000 IVS2 NEAX2000 IVS2 Table of Contents List of Figures List of Tables Purpose Outline of this ManualReference Manuals Chapter General Information System Outline SummaryPhysical Interface 30DTI Physical Interface 24DTIInterworking with Other Network SIGSystem Configuration Clock30DTI PLO Card Name and Function Card Name FunctionalSystem Capacity Description 24DTI 30DTISystem Conditions Time Slot Assignment ConditionTime Slot Allocation for DTI/DCH Card Time Slot Allocation for DTIService Features Connected Destination IndicationTerm Transit Counter Relaying 10 Transit CounterChapter Installation When PLUGGING/UNPLUGGING a Circuit Card PrecautionsWhen Holding a Circuit Card When Making a Switch Setting on a Circuit Card When Carrying a Circuit CardInstallation Required Equipment Equipment Description Quantity RemarksPN-30DTC-A PN-24DTA-CInstallation Procedure Installation Procedure for Q-SIGMounting DTI and DCH Card Mounting Conn Card Selection of PLO in MP Card DTI Cable Connection via MDF Cable Connection via MDFLocation of the AP Slots and the LTC Connectors for DTI Example of MDF Cross Connection for DTI DTI Cable Connection via Conn Card Cable Connection via the Conn CardExample of Coaxial Cable Connection Chapter System Data Programming HOW to Read this Chapter DTI Assignment Startdescription DataExample of 30DTI Description Data PatternsDCH Initial DCH Assignment CMA9 ENDTandem Connection Assignment Connected Destination Indication Assignment Chapter Circuit Card Information Circuit Card Information Mounting Location of Circuit Card PN-30DTC-A DTI PN-SC01 DCHList of Required Circuit Card PN-30DTC-A DTI PN-24DTA-C DTI PN-SC01 DCHPN-CP14 MP Lamp Color Function NameRUN CLKSwitch Name Setting Function Check Number Position SW2 OFFOFF OFF ModemSW4 Dip SW Down PN-30DTC-A DTI PCM FRMMfrm RMTSwitch Setting Function Check Name Number Position SensSource clock signal from network is JPS JPRRight LeftDTI0 DTI1 DTI2 DTI3 Conditions Remarks PN-24DTA-C DTI CRC Sense SW0 OFF MDFSW1 OFF DTI0 DTI1 DTI2 DTI3 DTI4 Conditions Remarks PN-SC01 DCH LPBSW0 OFF SW1 Dip SW PZ-M542 Conn Lamp Indications This card has no lampsJP1 Right JP0 RightJP2 Right PZ-M557 Conn Switch Name Setting Function Check Number Position
Related manuals
Manual 475 pages 726 b