NEC NEAX2000 IVS2 system manual DCH Assignment, CMA9 END

Page 44

CHAPTER 3 SYSTEM DATA PROGRAMMING

DCH Assignment

DCH ASSIGNMENT

START

CM05

CM06

CM35

DESCRIPTION

 

 

DATA

Assign an AP number to the DCH card.

 

Y=0

The AP number must match the SENS

(1)

04-15, 20-31: AP No.

switch setting on the DCH card.

(2)

32: DCH card for Q-SIG

INITIAL

 

 

 

Assign the DCH number to the AP

 

YY=08

number of DCH assigned by CM05.

(1)

0-7: DCH No.

INITIAL

(2)

04-15, 20-31: AP No. assigned by

 

 

CM05 Y=0

 

 

 

Assign the DCH number to the Q-SIG

 

YY=93 Assignment of DCH

trunk route assigned by CM30 YY=00.

(1)

00-63: B Channel Trunk Route No.

 

(2)

00-07: DCH No. assigned by CM06

NOTE: This data should be assigned to only the B Channel trunk routes.

CMA9

END

Assign the trunk number assigned by CM07 YY=01 to each DCH number for providing D Channel path between DTI and DCH.

YY=00

(1)0-7: DCH No. assigned by CM06

(2)000-255: Trunk No. assigned by CM07 YY=01

NEAX2000 IVS2 Q-SIG System Manual

Page 37

ND-70923 (E), Issue 1.0

Image 44
Contents SIG System Manual Liability Disclaimer NEAX2000 IVS2 NEAX2000 IVS2 Table of Contents List of Figures List of Tables Purpose Outline of this ManualReference Manuals Chapter General Information System Outline SummaryPhysical Interface 30DTI Physical Interface 24DTIInterworking with Other Network SIGSystem Configuration Clock30DTI PLO Card Name and Function Card Name FunctionalSystem Capacity Description 24DTI 30DTISystem Conditions Time Slot Assignment ConditionTime Slot Allocation for DTI/DCH Card Time Slot Allocation for DTIService Features Connected Destination IndicationTerm Transit Counter Relaying 10 Transit CounterChapter Installation When Holding a Circuit Card PrecautionsWhen PLUGGING/UNPLUGGING a Circuit Card When Making a Switch Setting on a Circuit Card When Carrying a Circuit CardInstallation Required Equipment Equipment Description Quantity RemarksPN-30DTC-A PN-24DTA-CInstallation Procedure Installation Procedure for Q-SIGMounting DTI and DCH Card Mounting Conn Card Selection of PLO in MP Card DTI Cable Connection via MDF Cable Connection via MDFLocation of the AP Slots and the LTC Connectors for DTI Example of MDF Cross Connection for DTI DTI Cable Connection via Conn Card Cable Connection via the Conn CardExample of Coaxial Cable Connection Chapter System Data Programming HOW to Read this Chapter DTI Assignment Startdescription DataExample of 30DTI Description Data PatternsDCH Initial DCH Assignment CMA9 ENDTandem Connection Assignment Connected Destination Indication Assignment Chapter Circuit Card Information Circuit Card Information Mounting Location of Circuit Card PN-30DTC-A DTI PN-SC01 DCHList of Required Circuit Card PN-30DTC-A DTI PN-24DTA-C DTI PN-SC01 DCHPN-CP14 MP Lamp Color Function NameRUN CLKSwitch Name Setting Function Check Number Position SW2 OFFOFF OFF ModemSW4 Dip SW Down PN-30DTC-A DTI PCM FRMMfrm RMTSwitch Setting Function Check Name Number Position SensSource clock signal from network is JPS JPRRight LeftDTI0 DTI1 DTI2 DTI3 Conditions Remarks PN-24DTA-C DTI CRC Sense SW0 OFF MDFSW1 OFF DTI0 DTI1 DTI2 DTI3 DTI4 Conditions Remarks PN-SC01 DCH LPBSW0 OFF SW1 Dip SW PZ-M542 Conn Lamp Indications This card has no lampsJP2 Right JP0 RightJP1 Right PZ-M557 Conn Switch Name Setting Function Check Number Position
Related manuals
Manual 475 pages 726 b