Emerson RTM-ATCA-7350 manual Zone 3 Connectors, 1 P30 Pinout, VGA Port Pin Assignment

Page 43

Zone 3 ConnectorsControls, LEDs and Connectors

Table 3-3 VGA Port Pin Assignment

Pin

Pin Name

Description

 

 

 

1

RED

Analog red video output signal.

 

 

 

2

GREEN

Analog green video output signal.

 

 

 

3

BLUE

Analog blue video output signal.

 

 

 

4

RESERVED1

Reserved.

 

 

 

5

RESERVED2

Reserved on RTM-ATCA-7350.

 

 

 

6

GROUND1

Connected to the logic ground of RTM-ATCA-7350.

 

 

 

7

GROUND2

Connected to the logic ground of RTM-ATCA-7350.

 

 

 

8

RESERVED3

Reserved on RTM-ATCA-7350.

 

 

 

9

RESERVED4

Reserved, Connected to 5VCC on RTM-ATCA-7350 through

 

 

a PTC resistor.

 

 

 

10

GROUND3

Connected to the logic ground of RTM-ATCA-7350.

 

 

 

11

RESERVED5

Reserved.

 

 

 

12

DDC DATA

DDC data pin for CRT.

 

 

 

13

HS

Horizontal sync for Monitor.

 

 

 

14

VS

Vertical sync for Monitor.

 

 

 

15

DDC CLK

DDC pin SCL for CRT.

 

 

 

3.3Zone 3 Connectors

Zone 3 is composed of three connectors, P30, P31, and P32. The three connectors are used to connect RTMs with RTM-ATCA-7350s. Zone 3 defines the following signals:

zUSB (USB)

zVGA

zIPMC SMBus

zPower (VCC 12VDC, VSBY 5V5)

zPCI-E Channels

zGeneral control signals (RTM PRESENT, RTM RST, LEDs)

zFabric channel port 0, port 1, port 2, port 3 for the ATCA-7350

3.3.1P30 Pinout

P30 uses a common 2mm HM connector. P31 uses a half-height ZD connector. P32 uses a ZD connector.

Refer to the PICMG specification for the location of the connectors.

The following table shows the P30 pinout. PinA1 on the server blade side is on the top of the connector while the server blade is placed top side upwards and the face plate is left.

RTM-ATCA-7350 Installation and Use (6806800H30F)

43

Image 43
Contents RTM-ATCA-7350 Contact Address Contents Contents Controls, LEDs and ConnectorsList of Tables Page Removing the Filler Blade List of FiguresPage About this Manual Overview of ContentsAbbreviations Bold ConventionsAbout this Manual Abbreviation Definition Notation DescriptionAbout this Manual Summary of ChangesPart Number Publication Date Description Comments and Suggestions Mechanical Data Mechanical Specifications of RTM-ATCA-7350Introduction Overview of RTM-ATCA-7350Standard Compliances Standard CompliancesOrdering Information Supported Board ModelsBoard Accessories Order Number Board AccessoriesAvailable Board Accessories Board AccessoriesIntroductionPage Overview Hardware Preparation and InstallationUnpacking and Inspecting RTM-ATCA-7350 Requirement Operating Non-Operating Environmental and Power RequirementsEnvironmental Requirements Environmental RequirementsPower RequirementsHardware Preparation and Installation Module Installation and RemovalPower Requirements Power RequirementsEjector Handles Hardware Preparation and Installation Ejector HandlesESD Prevention Wearing the ESD-Preventive Wrist Strap Installation PreparationsWearing the ESD-Preventive Wrist Strap Removing the Filler Blade Removing Filler BladesPrecautions Installing and Replacing Daughter CardsPreparations Preparations Hardware Preparation and InstallationGE Daughter Card Structure of RTM-ATCA-7350 Hardware Preparation and Installation GE Daughter CardGE Daughter Card Hardware Preparation and Installation Installing the GE Daughter CardFC Daughter Card Hardware Preparation and Installation FC Daughter CardFC Daughter Card Hardware Preparation and Installation Installing the FC Daughter CardInstalling RTM-ATCA-7350 Installing and Removing the RTM-ATCA-7350Installing RTM-ATCA-7350 Removing RTM-ATCA-7350 Hardware Preparation and Installation Removing RTM-ATCA-7350Removing RTM-ATCA-7350 Connecting External CablesHardware Preparation and Installation Connecting KVM Cables Connecting KVM CablesConnecting the Network Cables to RTM-ATCA-7350 Connecting Network CablesConnecting the Optical Fibers to RTM-ATCA-7350 Connecting Optical FibersControls, LEDs and Connectors LEDs Face Plate Connectors and LEDsLEDs Controls, LEDs and Connectors Indicators on the RTM-ATCA-7350Face PlateIndicator Color Meaning Description Label ConnectorsConnectors Controls, LEDs and Connectors Connectors and Indicators of RTM-ATCA-7350Pin Pin Name Description RTM-ATCA-7350 Front Plate VGA Port PinoutVGA Port Pin Assignment Zone 3 ConnectorsZone 3 ConnectorsControls, LEDs and Connectors 1 P30 PinoutPIN 31 Pinout Controls, LEDs and Connectors P31 Pinout2 P31 Pinout PIN 30 Pinout3 P32 Pinout P32 PinoutControls, LEDs and ConnectorsPIN 32 Pinout Controls, LEDs and ConnectorsP32 Pinout Functional Description Block DiagramDaughter Cards Functional Description GE Daughter Card Indicators Provided by the GE Daughter CardFC Daughter Card Functional Description Indicators Provided by the FC Daughter CardPage Related Documentation Emerson Network Power Embedded Computing DocumentsRelated Specifications Table A-2 Related Specifications