Philips V30 manual Extra Controls Adjust Moire

Page 11

OSD Adjustments (Continued)		107T5			11
	Go to cover page

4)Press the or button to select YES or NO. NO is the default. YES returns all settings to their original factory adjustments.

5) Press the button to confirm your selection and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS will be highlighted.

Smart Help After returning to MAIN CONTROLS . . .

.. . to continue to EXTRA CONTROLS, press the button until EXTRA CONTROLS is highlighted. Next, start with step 3 under EXTRA CONTROLS.

. . . to exit completely, press the button.

EXTRA CONTROLS

ADJUST MOIRE

EXTRA CONTROLS is a set of three features, including ADJUST MOIRE. Moire is a fringe pattern arising from the interference between two superimposed line patterns. To adjust your moire, follow the steps below. Note: Use only if necessary. By activating ADJUST MOIRE, sharpness can be affected.

1)Press the button on the monitor. The MAIN CONTROLS window appears.

2)Press the DOWN CURSOR button until EXTRA CONTROLS is highlighted.

4)Press the button. The ADJUST MOIRE window appears. HORIZONTAL will be highlighted.

5)To adjust the horizontal moire, press the or button.

6)When the horizontal moire is adjusted, press the button to highlight

VERTICAL.

7)To adjust the vertical moire, press the or button.

8)When the vertical moire is adjusted, press the button to return to the EXTRA CONTROLS window. BACK TO MAIN CONTROLS will be highlighted.

Smart Help After returning to MAIN CONTROLS . . .

.. . to continue to DEGAUSS, press the button until DEGAUSS is highlighted. Next, start with step 3 under EXTRA CONTROLS, DEGAUSS.

. . . to exit completely, press the button.

3) Press the button. The EXTRA CONTROLS window appears. will ADJUST MOIRE will be highlighted.

Image 11

Contents Auto Scan Colour Monitor ChassisV30 ServiceImportant Safety Notice This monitor has 8 factory-preset modes as indicated Technical DataRear view Front control Front ViewOSD Tree OSD menu treeLanguage Brightness OSD AdjustmentsZoom Adjust Shape Adjust Side Angles Reset to Factory Settings Extra Controls Adjust Moire Degauss OSD Adjustments , TroubleshootingLock/Unlock, Factory Mode, Burn In, Service Mode Wiring Diagram Clip Pedestal assy Screw CRT grouding wirel Video PanelMechanical Instructions GeneralScrew Video panel Main panel Main panel with Bottom TrayESD Are indicated by the symbolMain chassis alignment ================== Electrical InstructionsGeneral point ========== Pre warm-up ==========CRT Default settings ============== Adjustment procedureFocus adjustment ============= Adjustment of Moir ================General DDC InstructionsMethod 2 After create a shortcut of EDID301.EXE Configuration and procedureInstallation of EDID301.EXE Method 1 Start on DDC program This is for initialize alignment boxModify DDC data Monitor Serial No Videocard PrinterportLTP1 DC Power ~12 Video cableModify DDC data verify Edid version, week, year Read DDC data from monitorSave DDC data Confirm Serial Number in User ModeWrite DDC data Exit DDC program DDC only was disabled as shown in FigLoad DDC data PHL Hex Data of DDC2B27X 28X 107T5 Function Block of V30 107T5 VideoMain PCB Schematic Diagram of Main board107T5 A. of Main board A. of Main board Video PCB Schematic Diagram of Video boardA. of Video board A. of Video board Control PCB Schematic Diagram of Control boardA. of Control board Exploded View Model V30 107T50/00 Recommend Parts ListModel V30 107T50/00 Spare Parts ListAudio Panel LOW Emission MPRII/TCO99/TCO95 optional General Product SpecificationIndex 5903 General description Electrical characteristicsIntroduction 64.0 KHz 60Hz Vesa Factory preload modes Sync width 069 ms Sync polarity Total size 11.764 Display sizeDisplay size 11.093 Rear porch 222 us 578 ms Sync width Total size 21.333 13.333 Display size 16.162 = 12.8 ms Rear porch 200 us 607 ms Sync width 106 ms Sync. polarity Display size 12.552 Rear porch 911 us 784 ms Sync width Total size 13.853 Display sizeTotal size 13.417 Display size 59012 25.0 1 KV Ib=0 Power supplyVertical scanning Scanning frequency 50 160 Hz Shift range Implosion protection By P-Mini-rim-bandDisplay Light Output MVpp cross hatch Max. Y. min Non-linearity = 100% Image size For preset modes only100% MaxFor SRGB = 0.313 For 6500 K 015Finland Norway SwitzerlandBelgium Sweden200 Tilt and swivel base Tilt angleSets Layer Block Blocks / Container Total Sets Nsta Taiwan FinlandNBR. of Failure Sets Practice of Mtbf =FIG-1 Image Dimension FIG-2 Image Centering FIG-3 Image Rotation FIG-4 Image Geometry FIG-5 Contrast and Brightness Measurement Area FIG-6 Misconvergence 230 mm Focus check character Repair Flow Chart 2V ABL = +Check list CheckRepair Flow Chart Check sync Check idle status sda=pin32=hi scl=pin31=hi EepromEwdrv Vblk Compatibility InstallationLightFrame for Windows DefinitionsLightFrame for Windows UninstallIcon and Colors How to Deactivate LightFrameHow To Activate LightFrame Operating LightFrameScreen button Full screen First target selected Window restored LF suspendUser clicks off or full screen User clicks fullAttachment of SMDs Repair TipsGeneral cautions on handling and storage Removal of SMDsRequired =0.09+R ohm, R is the resistance of the mains cord Safety test requirementsTest 2820VDC 1700VDC Voltage 2000VAC 1200VAC Test current 25A,AC Test timeMenu locked General Troubleshooting GuideBuzzing sound when powering on OSD mainYES END No DISPLAY, but LED is on Or LED is amberyellowPicture is too bright or dark SettingsPlug & Play is not Active normally Power management function is not active Buzzing sound when powering on No Power / LED is off YES Color has IrregularityPress the OK Picture distortion is Not adjusted normallyPicture is not stable Need to change display size and adjust distortion Color Patterns visible On the screen Moire OSD Main Menu Locked Repair the monitor Environment problemVideo system Problem It is need to checkMissing Color Does degaussing resolve ? Color Purity104 107T5 107T5 105 CustoMax Colorific USB 107T5 109