Philips V30 manual Display Light Output

Page 56

56

107T5

Go to cover page

GENERAL PRODUCT SPECIFICATION

3.6 RGB Amplifier
3.6.1 Video amplifiers
Dot Rate	: 108 MHz
Over / undershoot	: 15% Max. (Transient response)
Sag	: 5% Max. (pulses of 0.70H)
Black level shift	: 5% Max.

3.6.2Brightness and Contrast

Reference mode 68.7 KHZ/85 HZ full white pattern.

DISPLAY LIGHT OUTPUT

Brightness

Contrast

Light output (full white)

Minimum

Minimum

not visible

Center

Maximum

30 5 FL.

100mmx100mm block

Brightness at center and contrast at maximum light output is 41+/-6 FL.

sRGB : When sRGB mode is selected, the light output (Full white pattern) shall be 23 +/- 3FL regardless of main contrast and brightness controls. Adjusting contrast or brightness will auto exit sRGB mode and go to 6500K mode.

3.6.3Raster light output

Apply 68.7KHz/85Hz mode with no video pattern, set brightness at center(50%) and contrast control at minimum(0%).

The light output on the screen center should be < 0.2FL.

3.7Variation of image size ( For preset modes only )

Due to brightness change : 1.0 %

Long term (Static)	: <1.50mm on left/right side
(See Fig.7)	<1.20mm on top/bottom side
Due to aging
(25 C, 300 hrs)	: 1.0 %
Due to mains voltage
variation ( 10% )	: 1.0 %

3.8Degaussing

An automatic degaussing circuit is provided which requires no intervention. The degaussing shall be activated and work effectively at the time of switch-on or switch-on again or pressing the manual degaussing key after the degaussing circuit has been switched off for longer than 30 minutes

(The PTC should be completely cooled off).

				17" V30 GS4 107T5-71K CMTR
				TYPE		: 107T51/00
				TYPE		: 107T51/00
2003-01-07				BRAND		: PHILIPS
2003-01-07
		Wayne Lin						30
						2003-01-07

59014

Image 56

Contents Service Auto Scan Colour Monitor ChassisV30Important Safety Notice Technical Data This monitor has 8 factory-preset modes as indicatedFront View Rear view Front controlOSD menu tree OSD TreeOSD Adjustments Language BrightnessZoom Adjust Shape Adjust Side Angles Reset to Factory Settings Extra Controls Adjust Moire OSD Adjustments , Troubleshooting DegaussLock/Unlock, Factory Mode, Burn In, Service Mode Wiring Diagram CRT grouding wirel Video Panel Mechanical InstructionsGeneral Clip Pedestal assy ScrewMain panel with Bottom Tray Screw Video panel Main panelAre indicated by the symbol ESDElectrical Instructions General point ==========Pre warm-up ========== Main chassis alignment ==================CRT Adjustment procedure Focus adjustment =============Adjustment of Moir ================ Default settings ==============DDC Instructions GeneralConfiguration and procedure Installation of EDID301.EXE Method 1 Start on DDC programThis is for initialize alignment box Method 2 After create a shortcut of EDID301.EXEVideocard PrinterportLTP1 DC Power ~12 Video cable Modify DDC data verify Edid version, week, yearRead DDC data from monitor Modify DDC data Monitor Serial NoSave DDC data Confirm Serial Number in User ModeWrite DDC data Exit DDC program DDC only was disabled as shown in FigLoad DDC data Hex Data of DDC2B PHL27X 28X 107T5 Video Function Block of V30 107T5Schematic Diagram of Main board Main PCB107T5 A. of Main board A. of Main board Schematic Diagram of Video board Video PCBA. of Video board A. of Video board Schematic Diagram of Control board Control PCBA. of Control board Exploded View Recommend Parts List Model V30 107T50/00Spare Parts List Model V30 107T50/00Audio Panel General Product Specification LOW Emission MPRII/TCO99/TCO95 optionalIndex 5903 General description Electrical characteristicsIntroduction 64.0 KHz 60Hz Vesa Factory preload modes Sync width 069 ms Sync polarity Total size 11.764 Display sizeDisplay size 11.093 Rear porch 222 us 578 ms Sync width Total size 21.333 13.333 Display size 16.162 = 12.8 ms Rear porch 200 us 607 ms Sync width 106 ms Sync. polarity Display size 12.552 Rear porch 911 us 784 ms Sync width Total size 13.853 Display sizeTotal size 13.417 Display size 59012 Power supply Vertical scanning Scanning frequency 50 160 Hz Shift rangeImplosion protection By P-Mini-rim-band 25.0 1 KV Ib=0Display Light Output MVpp cross hatch Image size For preset modes only 100%Max Max. Y. min Non-linearity = 100%For 6500 K 015 For SRGB = 0.313Switzerland BelgiumSweden Finland Norway200 Tilt and swivel base Tilt angleSets Layer Block Blocks / Container Total Sets Nsta Finland TaiwanPractice of Mtbf = NBR. of Failure SetsFIG-1 Image Dimension FIG-2 Image Centering FIG-3 Image Rotation FIG-4 Image Geometry FIG-5 Contrast and Brightness Measurement Area FIG-6 Misconvergence 230 mm Focus check character Repair Flow Chart = + 2V ABLCheck Check listRepair Flow Chart Check sync Eeprom Check idle status sda=pin32=hi scl=pin31=hiEwdrv Vblk Installation LightFrame for WindowsDefinitions CompatibilityUninstall LightFrame for WindowsHow to Deactivate LightFrame How To Activate LightFrameOperating LightFrame Icon and ColorsFirst target selected Window restored LF suspend User clicks off or full screenUser clicks full Screen button Full screenRepair Tips General cautions on handling and storageRemoval of SMDs Attachment of SMDsSafety test requirements Test 2820VDC 1700VDC Voltage 2000VAC 1200VACTest current 25A,AC Test time Required =0.09+R ohm, R is the resistance of the mains cordGeneral Troubleshooting Guide Buzzing sound when powering onOSD main Menu lockedNo DISPLAY, but LED is on Or LED is amberyellow YES ENDSettings Picture is too bright or darkPlug & Play is not Active normally Power management function is not active Buzzing sound when powering on No Power / LED is off Color has Irregularity YESPicture distortion is Not adjusted normally Press the OKPicture is not stable Need to change display size and adjust distortion Color Patterns visible On the screen Moire OSD Main Menu Locked Environment problem Video system ProblemIt is need to check Repair the monitorMissing Color Color Purity Does degaussing resolve ?104 107T5 107T5 105 CustoMax Colorific USB 107T5 109