Philips V30 manual Vertical scanning Scanning frequency 50 160 Hz Shift range, Power supply

Page 55

GENERAL PRODUCT SPECIFICATION

3.2.1	Horizontal scanning
	Scanning frequency	: 30 - 71 KHz
	H-shift range	: 10 mm Min. (for preset modes only)
3.2.2	Vertical scanning
	Scanning frequency	: 50 - 160 Hz
	V-shift range	: 10 mm min. (for preset modes only)

3.3Power supply

107T5

55

Go to cover page

The display device maintains the specified performance in the range described as below :

Type	Mains current	Mains Voltage	Mains freq.
230V version	1.5A Max.	90 - 264 VAC	60 +/- 3 Hz
Power consumption : 75 Watts Max.
Power cord length	: 1.5M
Power cord type	: 3 lead plug power cord
	with protective earth plug or IBM hooded

3.4Power saving management system

		Signal		Compliance	Power
				Requirement
	H-Sync	V-Sync	Video	Requirement
	H-Sync	V-Sync	Video

On	Active	Active	Active	Mandatory	<= 75w

Off	Inactive	Active	Blanked	Mandatory	<=	2 w

Off	Active	Inactive	Blanked	Mandatory	<=	2 w

Off	Inactive	Inactive	Blanked	Mandatory	<=	2 w

3.5CRT Description

This display unit employs a high resolution CRT complying with the following specifications :

Dimensions	: 17 inches flat/square screen
Pitch	: 0.25mm dotted with black matrix
Deflection angle	: 90 degrees
Light transmission	: 50%(CPT), 52.8%(LG), 52.6%(SDI)
Face treatment	: AGARAS
Implosion protection	: By P-Mini-rim-band.
EHT	: 25.0 1 KV (Ib=0)
Visible screen area	: 325.1 mm x 243.8 mm
CRT Source	: CPT, LG, SDI

				17" V30 GS4 107T5-71K CMTR
				TYPE		: 107T51/00
				TYPE		: 107T51/00
2003-01-07				BRAND		: PHILIPS
2003-01-07
		Wayne Lin						30
						2003-01-07

59013

Image 55

Contents Auto Scan Colour Monitor ChassisV30 ServiceImportant Safety Notice This monitor has 8 factory-preset modes as indicated Technical DataRear view Front control Front ViewOSD Tree OSD menu treeLanguage Brightness OSD AdjustmentsZoom Adjust Shape Adjust Side Angles Reset to Factory Settings Extra Controls Adjust Moire Degauss OSD Adjustments , TroubleshootingLock/Unlock, Factory Mode, Burn In, Service Mode Wiring Diagram Clip Pedestal assy Screw CRT grouding wirel Video PanelMechanical Instructions GeneralScrew Video panel Main panel Main panel with Bottom TrayESD Are indicated by the symbolMain chassis alignment ================== Electrical InstructionsGeneral point ========== Pre warm-up ==========CRT Default settings ============== Adjustment procedureFocus adjustment ============= Adjustment of Moir ================General DDC InstructionsMethod 2 After create a shortcut of EDID301.EXE Configuration and procedureInstallation of EDID301.EXE Method 1 Start on DDC program This is for initialize alignment boxModify DDC data Monitor Serial No Videocard PrinterportLTP1 DC Power ~12 Video cableModify DDC data verify Edid version, week, year Read DDC data from monitorWrite DDC data Confirm Serial Number in User ModeSave DDC data Load DDC data DDC only was disabled as shown in FigExit DDC program PHL Hex Data of DDC2B27X 28X 107T5 Function Block of V30 107T5 VideoMain PCB Schematic Diagram of Main board107T5 A. of Main board A. of Main board Video PCB Schematic Diagram of Video boardA. of Video board A. of Video board Control PCB Schematic Diagram of Control boardA. of Control board Exploded View Model V30 107T50/00 Recommend Parts ListModel V30 107T50/00 Spare Parts ListAudio Panel LOW Emission MPRII/TCO99/TCO95 optional General Product SpecificationIndex 5903 Introduction Electrical characteristicsGeneral description 64.0 KHz 60Hz Vesa Factory preload modes Display size 11.093 Rear porch 222 us 578 ms Sync width Total size 11.764 Display sizeSync width 069 ms Sync polarity Total size 21.333 13.333 Display size 16.162 = 12.8 ms Rear porch 200 us 607 ms Sync width 106 ms Sync. polarity Total size 13.417 Display size Total size 13.853 Display sizeDisplay size 12.552 Rear porch 911 us 784 ms Sync width 59012 25.0 1 KV Ib=0 Power supplyVertical scanning Scanning frequency 50 160 Hz Shift range Implosion protection By P-Mini-rim-bandDisplay Light Output MVpp cross hatch Max. Y. min Non-linearity = 100% Image size For preset modes only100% MaxFor SRGB = 0.313 For 6500 K 015Finland Norway SwitzerlandBelgium SwedenSets Layer Block Blocks / Container Total Sets Tilt and swivel base Tilt angle200 Nsta Taiwan FinlandNBR. of Failure Sets Practice of Mtbf =FIG-1 Image Dimension FIG-2 Image Centering FIG-3 Image Rotation FIG-4 Image Geometry FIG-5 Contrast and Brightness Measurement Area FIG-6 Misconvergence 230 mm Focus check character Repair Flow Chart 2V ABL = +Check list CheckRepair Flow Chart Check sync Check idle status sda=pin32=hi scl=pin31=hi EepromEwdrv Vblk Compatibility InstallationLightFrame for Windows DefinitionsLightFrame for Windows UninstallIcon and Colors How to Deactivate LightFrameHow To Activate LightFrame Operating LightFrameScreen button Full screen First target selected Window restored LF suspendUser clicks off or full screen User clicks fullAttachment of SMDs Repair TipsGeneral cautions on handling and storage Removal of SMDsRequired =0.09+R ohm, R is the resistance of the mains cord Safety test requirementsTest 2820VDC 1700VDC Voltage 2000VAC 1200VAC Test current 25A,AC Test timeMenu locked General Troubleshooting GuideBuzzing sound when powering on OSD mainYES END No DISPLAY, but LED is on Or LED is amberyellowPicture is too bright or dark SettingsPlug & Play is not Active normally Power management function is not active Buzzing sound when powering on No Power / LED is off YES Color has IrregularityPress the OK Picture distortion is Not adjusted normallyPicture is not stable Need to change display size and adjust distortion Color Patterns visible On the screen Moire OSD Main Menu Locked Repair the monitor Environment problemVideo system Problem It is need to checkMissing Color Does degaussing resolve ? Color Purity104 107T5 107T5 105 CustoMax Colorific USB 107T5 109