ADVANCED FUNCTIONS

Manual SPEAKER Setup

The AVR 460/AVR 360 is flexible and may be configured for most speakers, and to compensate for the acoustic characteristics of your room.

The EzSet/EQ process automatically detects the capabilities of each speaker, and optimizes the AVR 460/AVR 360’s performance. If you are unable to run EzSet/EQ calibration, or if you wish to make further adjustments, use the Manual Speaker Setup on-screen menus.

Before beginning, place your loudspeakers as explained in the Speaker Placement section, and connect them to the AVR. Consult the owner’s guide for the speakers or the manufacturer’s Web site for the frequency range specification. Although you may set the output levels “by ear,” an SPL (sound- pressure level) meter purchased at a local electronics store will provide greater accuracy.

Record your configuration settings in Tables A3 through A11 in the appendix for easy re-entry after a system reset, or if the AVR’s Master Power Switch is turned off or the unit is unplugged for more than four weeks.

NOTE: When using the AVR’s Speaker Setup menus, select a video output resolution of 720p or higher to view graphics that simplify configuration.

Step One – Determine Speaker Crossover

Without using the EzSet/EQ process, the AVR 460/AVR 360 can’t detect how many speakers you’ve connected to it; nor can it determine their capabilities. Consult the speaker’s technical specifications and locate the frequency response, usually given as a range, e.g., 100Hz – 20kHz (±3dB). Write down the lowest frequency that each of your main speakers is capable of playing (100Hz in the example) as the crossover in Table A3 in the appendix. This is not the same as the crossover frequency listed in the speaker’s specifications. For the subwoofer, write down the transducer size.

The receiver’s bass management determines which speakers will be used to play back the low-frequency (bass) portion of the source program. Sending the lowest notes to small satellite speakers won’t sound right, and may even damage the speaker. The highest notes may not be heard at all through the subwoofer.

With proper bass management, the AVR 460/AVR 360 divides the source signal at a crossover point. All information above the crossover point is played through the satellite speaker, and all information below the crossover point is played through the subwoofer. Each loudspeaker in your system performs at its best, delivering an enjoyable sound experience.

Step Two – Measure Speaker Distances

Ideally, all of your speakers would be placed in a circle, with the listening position at the center. However, you may have had to place some speakers a little further away from the listening position than others. Sounds that are supposed to arrive simultaneously from different speakers may blur, due to different arrival times.

Use the AVR’s delay adjustment to compensate for real-world speaker placements.

Measure the distance from each speaker to the listening position, and write it down in Table A4 in the appendix. Even if all of your speakers are the same distance from the listening position, enter your speaker distances as described in Step Three.

Step Three – Manual Setup Menu

Now you are ready to program the receiver. Sit in the usual listening position and make the room as quiet as possible.

With the receiver and video display turned on, press the Setup Button to display the menu system. Use the L Button to move the cursor to the Speaker Setup line, and press the OK Button to display the Speaker Setup menu. See Figure 20 in the Basic Manual.

If you have run the EzSet/EQ process, the results were saved. To tweak the EzSet/EQ results, or to configure the AVR 460/AVR 360 from scratch, select Manual Setup. A screen similar to the one shown in Figure 30 will appear.

Figure 30 – Manual Speaker Setup Menu

NOTE: All of the speaker setup submenus include the Back option, as shown at the bottom of Figure 30. To save the current settings, select the Back option.

To reconfigure the speakers from scratch, select the Reset option.

For best results, adjust the submenus in this order: Number of Speakers, Crossover (Size), Sub Mode, Distance and Level Adjust.

Number of Speakers

Move the cursor to the Number of Speakers line and press the OK Button. See Figure 31.

Figure 31 – Number of Speakers Menu

Program the correct setting for each speaker group: ON when the speakers are present in the system, and OFF for positions where no speakers are installed. The Front Left & Right speakers are always ON and may not be disabled. Any changes will be reflected in the total number of speakers displayed at the top of the screen.

The setting for the surround back speakers includes a third option: Zone 2. The AVR 460/AVR 360 is capable of multizone operation, supporting placement of a pair of speakers in another room. The AVR 460/AVR 360’s assignable surround back amplifier channels make multizone operation easier than ever, since an external power amplifier is not required. Select the Zone 2 option

at this line, and connect the Surround Back Speaker Outputs to loudspeakers located in the remote room.

6

Page 5 Page 7
Page 6
Image 6
Harman-Kardon AVR 460 manual Manual Speaker Setup, Step One Determine Speaker Crossover, Step Two Measure Speaker Distances
Page 5 Page 7

AVR 360, AVR 460 specifications

The Harman-Kardon AVR 460 and AVR 360 are two outstanding models from the renowned audio equipment manufacturer, both designed to deliver high-quality sound experiences for home entertainment systems. These receivers combine advanced technologies with user-friendly features, making them popular choices among audiophiles and casual listeners alike.

The Harman-Kardon AVR 460 is equipped with a robust 7.1 channel surround sound system, boasting a total power output of 100 watts per channel. This receiver supports high-definition audio formats, including Dolby TrueHD and DTS-HD Master Audio, ensuring immersive sound quality for movies and music alike. One of its standout features is the proprietary Harman Kardon Logic 7 technology, which enhances stereo sources to a multi-channel audio experience, maximizing the quality of any audio input.

On the other hand, the Harman-Kardon AVR 360 follows closely in features and audio performance, offering 7.1 channels as well but with a slightly lower power output of 80 watts per channel. It still excels in audio clarity and richness, making it suitable for any home theater setup. Both models provide extensive connectivity options, including HDMI inputs, legacy audio inputs, and built-in Bluetooth, allowing users to effortlessly stream music from their smartphones or tablets.

Another notable characteristic of the AVR 460 is its advanced video processing capabilities, enabling video upscaling to 1080p, ensuring that users can enjoy their content in the best possible resolution. Both receivers also incorporate multi-zone functionality, allowing different audio sources to be played in various rooms simultaneously. This feature makes them perfect for entertaining guests or enjoying music throughout the home.

The user interfaces for both models are designed with ease of use in mind, featuring intuitive on-screen menus and remote control functionality. They also support various audio calibration technologies, such as Harman's Room Correction, which optimizes sound output based on the specific acoustics of the listening environment.

In summary, the Harman-Kardon AVR 460 and AVR 360 are both exemplary audio/video receivers that combine advanced sound technologies, extensive connectivity options, and user-friendly features. Whether you are looking for immersive surround sound for movies or high-fidelity audio for music, these models are impressive choices that enhance any home theater setup, delivering exceptional performance for years to come.
Top Page Image Contents