Philips Unlock OSD Main Controls and Access Factory Mode for Monitors

Page 13

Lock/Unlock, Factory Mode, Burn In, Service Mode

107T5

 

13

￿ Go to cover page

OSD Lock

OSD lock is a feature which disables the OSD controls. It can be used when the monitor is set up for demonstration purposes or when

adjustment of the OSD is not desirable.

Switch on OSD lock feature:

Press and hold the button continuously for 15 seconds. Release the button when the message

"CONTROL MENU IS LOCKED" appears.

Switch off OSD lock feature:

Press and hold the button continuously for 15 seconds or until the message window "CONTROL MENU IS LOCKED" disappears, and

"MAIN CONTROLS" appears.

To access factory mode

1.Turn off monitor (don't turn off PC)

2.Press '" " and " " simultaneously on the front control

panel,then press " ",wait till the OSD menu with characters V30 107T5 V0.48 20021218 (below OSD menu)" come on the screen of monitor.

To access BURN IN mode

First of all, monitor displays an image.

1.Disconnect the video cable (interface cable).

2.Turn off monitor

3. Press '" " and " " simultaneously on the front control panel,then the BURN IN mode comes on the screen of monitor as below.

50 seconds around

5 seconds around

repeatly

4.Reconnect the video cable, then return to normal image.

SERVICE MODE (Indication-Factory mode)

02060

>------------------------

02060: stands for

1. using 10 hours already.

2. turn on/off 10 times.

3. using several hours + turn on/off monitor.

MODEL SELECT

V30 107T5 V0.48 20021218

Default setting of MODEL SELECT (Do not change it.)

MODEL SELECT

107T5

107B5 RESERVE RESERVE RESERVE SWDDC LF 3

Factory

Mode

Indicator

MODEL SELECT

V30 107T5 V0.48 20021218

3.If OSD menu disappears on the screen of monitor, press " " again (anytime), then the OSD menu comes on the screen again.

4.Using " " : to select OSD menu.

5. Using " " : to increase or decrease the setting.

6. Using " " to access/confirm the selection.

To leave factory mode

7.After alignment of factory mode, turn off monitor (if you do not turn off monitor, the OSD menu is always at the factory mode), then turn on monitor again (at this moment, the OSD menu goes back to user mode).

Image 13
Contents Auto Scan Colour Monitor ChassisV30 ServiceImportant Safety Notice This monitor has 8 factory-preset modes as indicated Technical DataRear view Front control Front ViewOSD Tree OSD menu treeLanguage Brightness OSD AdjustmentsZoom Adjust Shape Adjust Side Angles Reset to Factory Settings Extra Controls Adjust Moire Degauss OSD Adjustments , TroubleshootingLock/Unlock, Factory Mode, Burn In, Service Mode Wiring Diagram Mechanical Instructions CRT grouding wirel Video PanelGeneral Clip Pedestal assy ScrewScrew Video panel Main panel Main panel with Bottom TrayESD Are indicated by the symbolGeneral point ========== Electrical InstructionsPre warm-up ========== Main chassis alignment ==================CRT Focus adjustment ============= Adjustment procedureAdjustment of Moir ================ Default settings ==============General DDC InstructionsInstallation of EDID301.EXE Method 1 Start on DDC program Configuration and procedureThis is for initialize alignment box Method 2 After create a shortcut of EDID301.EXEModify DDC data verify Edid version, week, year Videocard PrinterportLTP1 DC Power ~12 Video cableRead DDC data from monitor Modify DDC data Monitor Serial NoWrite DDC data Confirm Serial Number in User ModeSave DDC data Load DDC data DDC only was disabled as shown in FigExit DDC program PHL Hex Data of DDC2B27X 28X 107T5 Function Block of V30 107T5 VideoMain PCB Schematic Diagram of Main board107T5 A. of Main board A. of Main board Video PCB Schematic Diagram of Video boardA. of Video board A. of Video board Control PCB Schematic Diagram of Control boardA. of Control board Exploded View Model V30 107T50/00 Recommend Parts ListModel V30 107T50/00 Spare Parts ListAudio Panel LOW Emission MPRII/TCO99/TCO95 optional General Product SpecificationIndex 5903 Introduction Electrical characteristicsGeneral description 64.0 KHz 60Hz Vesa Factory preload modes Display size 11.093 Rear porch 222 us 578 ms Sync width Total size 11.764 Display sizeSync width 069 ms Sync polarity Total size 21.333 13.333 Display size 16.162 = 12.8 ms Rear porch 200 us 607 ms Sync width 106 ms Sync. polarity Total size 13.417 Display size Total size 13.853 Display sizeDisplay size 12.552 Rear porch 911 us 784 ms Sync width 59012 Vertical scanning Scanning frequency 50 160 Hz Shift range Power supplyImplosion protection By P-Mini-rim-band 25.0 1 KV Ib=0Display Light Output MVpp cross hatch 100% Image size For preset modes onlyMax Max. Y. min Non-linearity = 100%For SRGB = 0.313 For 6500 K 015Belgium SwitzerlandSweden Finland NorwaySets Layer Block Blocks / Container Total Sets Tilt and swivel base Tilt angle200 Nsta Taiwan FinlandNBR. of Failure Sets Practice of Mtbf =FIG-1 Image Dimension FIG-2 Image Centering FIG-3 Image Rotation FIG-4 Image Geometry FIG-5 Contrast and Brightness Measurement Area FIG-6 Misconvergence 230 mm Focus check character Repair Flow Chart 2V ABL = +Check list CheckRepair Flow Chart Check sync Check idle status sda=pin32=hi scl=pin31=hi EepromEwdrv Vblk LightFrame for Windows InstallationDefinitions CompatibilityLightFrame for Windows UninstallHow To Activate LightFrame How to Deactivate LightFrameOperating LightFrame Icon and ColorsUser clicks off or full screen First target selected Window restored LF suspendUser clicks full Screen button Full screenGeneral cautions on handling and storage Repair TipsRemoval of SMDs Attachment of SMDsTest 2820VDC 1700VDC Voltage 2000VAC 1200VAC Safety test requirementsTest current 25A,AC Test time Required =0.09+R ohm, R is the resistance of the mains cordBuzzing sound when powering on General Troubleshooting GuideOSD main Menu lockedYES END No DISPLAY, but LED is on Or LED is amberyellowPicture is too bright or dark SettingsPlug & Play is not Active normally Power management function is not active Buzzing sound when powering on No Power / LED is off YES Color has IrregularityPress the OK Picture distortion is Not adjusted normallyPicture is not stable Need to change display size and adjust distortion Color Patterns visible On the screen Moire OSD Main Menu Locked Video system Problem Environment problemIt is need to check Repair the monitorMissing Color Does degaussing resolve ? Color Purity104 107T5 107T5 105 CustoMax Colorific USB 107T5 109