EN 55022 Compliance Czech Republic Only, Varning

Page 21

5. Regulatory Infomation

EN 55022 Compliance (Czech Republic Only)

Polish Center for Testing and Certification Notice

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.

The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible.

A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/E-06251.

North Europe (Nordic Countries) Information

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation

ADVARSEL:

S Ø R G V E D P L AC E R I N G E N F O R , AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.

Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.

Plassering/Ventilasjon

ADVARSEL:

NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.

Contents Troubleshooting & FAQs Customer care and warranty221S3U Table of Contents Warnings 1.1 Safety precautions and mainte- nanceService 1.2 Notational DescriptionsThe casing cover should be opened only by qualified service personnel Temperature 0-40C 32-95F Humidity 20-80% RH1.3 Disposal of product and packing material Waste Electrical and Electronic Equipment WEEERecycling Information for Customers 2. Setting up the monitor 2.1 InstallationStart Connecting to your laptop Insert the height adjustment pin lock before lifting the monitor Remove the height adjustment pin lock before adjusting the height70mm Resolution notification2.2 Remove Base Stand and Base Remove the Base Stand1. Extend the monitor base to its maximum height 1. Remove the 8 screw covers Remove the base Condition For VESA standard mounting applications2. Remove the 4 screws and then remove the base from the monitor 100mm 100mm3. USB monitor operation 3.2 DisplayLink Graphics Software Installation3.1 Introduction 3. USB monitor operation3.3 How to control the display Use the drop down list to select a display to be configured DisplayLink Manager Sub-menu Option Menu Option 4.Technical Specifications 4. Technical SpecificationsThe USB monitor works with USB 2.0 480 Mbps 4.1 Resolution & Preset Modes5. Regulatory Information FCC Declaration of Conformity EN 55022 Compliance Czech Republic Only Polish Center for Testing and Certification NoticeNorth Europe Nordic Countries Information Placering/Ventilation VARNINGErgonomie Hinweis nur Deutschland 环保使用期限 China RoHS6. Customer care and warranty 6.1 Philips’ Flat Panel Monitors Pixel Defect Policy6. Customer care and warranty ACCEPTABLE LEVEL BRIGHT DOT DEFECTSBLACK DOT DEFECTS TOTAL DOT DEFECTSCountry 6.2 Customer Care & WarrantyConsumer care number PriceCall center PT. Gadingsari elektronika Prima Contact Information for APMEA region7.1 Troubleshooting 7. Troubleshooting & FAQsCommon Problems Imaging Problemssolvents such as ethyl alcohol, ethanol General FAQssystem systems other than Windows USB monitor FAQsSpecifications are subject to change without notice 2012 Koninklijke Philips Electronics N.V. All rights reservedVersion M3221SUE1T