Philips 221S3UCB Notational Descriptions, Temperature 0-40C 32-95F Humidity 20-80% RH, Service

Page 4

1.Important

Temperature: 0-40°C 32-95°F

Humidity: 20-80% RH

Important information for Burn-in/Ghost image

Always activate a moving screen saver program when you leave your monitor unattended. Always activate a periodic screen refresh application if your moni- tor will display unchanging static content. Uninterrupted display of still or static im- ages over an extended period may cause “burn in”, also known as “after-imaging” or “ghost imaging”, on your screen.

"Burn-in", "after-imaging", or "ghost imag- ing" is a well-known phenomenon in LCD panel technology. In most cases, the “burned in” or “after-imaging” or “ghost imaging” will disappear gradually over a period of time after the power has been switched off.

Warning

Failure to activate a screen saver, or a periodic screen refresh application may result in severe “burn-in” or “after-image” or “ghost image” symptoms will not disappear and cannot be repaired.The damage mentioned above is not covered under your warranty.

Service

The casing cover should be opened only by qualified service personnel.

If there is any need for any document for repair or integration, please contact with your local service center. (please refer to the chapter of "Consumer Information Center")

For transportation information, please refer to "Technical Specifications".

Do not leave your monitor in a car/trunk under direct sun light.

Note

Consult a service technician if the monitor does not operate normally, or you are not sure what procedure to take when the operating instructions given in this manual have been followed.

1.2 Notational Descriptions

The following subsections describe notational conventions used in this document.

Notes, Cautions and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type.These blocks contain notes, cautions or warnings.They are used as follows:

Note

This icon indicates important information and tips that help you make better use of your computer system.

Caution

This icon indicates information that tells you how to avoid either potential damage to hardware or loss of data.

Warning

This icon indicates the potential for bodily harm and tells you how to avoid the problem.

Some warnings may appear in alternate formats and may not be accompanied by an icon. In such cases, the specific presentation of the warning is mandated by the relevant regulatory authority.

2

Image 4
Contents Customer care and warranty Troubleshooting & FAQs221S3U Table of Contents 1.1 Safety precautions and mainte- nance Warnings1.2 Notational Descriptions ServiceThe casing cover should be opened only by qualified service personnel Temperature 0-40C 32-95F Humidity 20-80% RHWaste Electrical and Electronic Equipment WEEE 1.3 Disposal of product and packing materialRecycling Information for Customers 2.1 Installation 2. Setting up the monitorStart Connecting to your laptop Remove the height adjustment pin lock before adjusting the height Insert the height adjustment pin lock before lifting the monitor70mm Resolution notificationRemove the Base Stand 2.2 Remove Base Stand and Base1. Extend the monitor base to its maximum height Remove the base Condition For VESA standard mounting applications 1. Remove the 8 screw covers2. Remove the 4 screws and then remove the base from the monitor 100mm 100mm3.2 DisplayLink Graphics Software Installation 3. USB monitor operation3.1 Introduction 3. USB monitor operation3.3 How to control the display Use the drop down list to select a display to be configured DisplayLink Manager Sub-menu Option Menu Option 4. Technical Specifications 4.Technical Specifications4.1 Resolution & Preset Modes The USB monitor works with USB 2.0 480 Mbps5. Regulatory Information FCC Declaration of Conformity Polish Center for Testing and Certification Notice EN 55022 Compliance Czech Republic OnlyNorth Europe Nordic Countries Information Placering/Ventilation VARNINGErgonomie Hinweis nur Deutschland China RoHS 环保使用期限6.1 Philips’ Flat Panel Monitors Pixel Defect Policy 6. Customer care and warranty6. Customer care and warranty BRIGHT DOT DEFECTS ACCEPTABLE LEVELBLACK DOT DEFECTS TOTAL DOT DEFECTS6.2 Customer Care & Warranty CountryConsumer care number PriceCall center Contact Information for APMEA region PT. Gadingsari elektronika Prima7. Troubleshooting & FAQs 7.1 TroubleshootingCommon Problems Imaging ProblemsGeneral FAQs solvents such as ethyl alcohol, ethanolUSB monitor FAQs system systems other than Windows2012 Koninklijke Philips Electronics N.V. All rights reserved Specifications are subject to change without noticeVersion M3221SUE1T