Philips 221S3UCB specs

Page 13

3. USB monitor operation

2. Setting the Display

Follow this procedure to set the display.

To set the display

2.1.Open Screen Resolution.

2.2.Set the display options. Refer to the table below for details on each option.

Menu Option	Sub-menu Option	Description
Display		Use the drop down list to select a display to be configured.

Resolution		Use the drop down list and user the slider to choose a
		resolution.
Orientation (Use	Landscape	Sets the display to landscape view
this function if	Portrait	Sets the display to portrait mode
you upgrade with	Landscape (flipped)	Sets the display to upside down landscape mode
Ergonomics base)	Portrait (flipped)	Sets the display to upside down portrait mode
Multiple displays	Duplicates these	Reproduces the main display on the second display.
	displays
	Extend these displays	Extends the main display onto the secondary display.
	Show Desktop only	The desktop appears on the display marked 1.The display
	on 1	marked 2 becomes blank.
	Shows Desktop only	The desktop appears on the display marked 2.The display
	on 2	marked 1 becomes blank.

Table 1:WDP Options

To control the behaviour of an attached DisplayLink display, it is also possible to use Windows key+P to display the menu (and cycle through it) to switch mode.

3.To control the Display

3.1.Select the Windows key+P.The following menu appears.

3.2. Click on one of the options.The display updates to reflect your choice.

The DisplayLink icon application

You can configure the behaviour of the DisplayLink USB Graphics through the DisplayLink icon application on the taskbar, where present.

Contents Customer care and warranty Troubleshooting & FAQs221S3U Table of Contents Warnings 1.1 Safety precautions and mainte- nanceService 1.2 Notational DescriptionsThe casing cover should be opened only by qualified service personnel Temperature 0-40C 32-95F Humidity 20-80% RHWaste Electrical and Electronic Equipment WEEE 1.3 Disposal of product and packing materialRecycling Information for Customers 2.1 Installation 2. Setting up the monitorStart Connecting to your laptop Insert the height adjustment pin lock before lifting the monitor Remove the height adjustment pin lock before adjusting the height70mm Resolution notificationRemove the Base Stand 2.2 Remove Base Stand and Base1. Extend the monitor base to its maximum height 1. Remove the 8 screw covers Remove the base Condition For VESA standard mounting applications2. Remove the 4 screws and then remove the base from the monitor 100mm 100mm3. USB monitor operation 3.2 DisplayLink Graphics Software Installation3.1 Introduction 3. USB monitor operation3.3 How to control the display Use the drop down list to select a display to be configured DisplayLink Manager Sub-menu Option Menu Option 4.Technical Specifications 4. Technical SpecificationsThe USB monitor works with USB 2.0 480 Mbps 4.1 Resolution & Preset Modes5. Regulatory Information FCC Declaration of Conformity EN 55022 Compliance Czech Republic Only Polish Center for Testing and Certification NoticeNorth Europe Nordic Countries Information Placering/Ventilation VARNINGErgonomie Hinweis nur Deutschland 环保使用期限 China RoHS6.1 Philips’ Flat Panel Monitors Pixel Defect Policy 6. Customer care and warranty6. Customer care and warranty ACCEPTABLE LEVEL BRIGHT DOT DEFECTSBLACK DOT DEFECTS TOTAL DOT DEFECTSCountry 6.2 Customer Care & WarrantyConsumer care number PriceCall center PT. Gadingsari elektronika Prima Contact Information for APMEA region7.1 Troubleshooting 7. Troubleshooting & FAQsCommon Problems Imaging Problemssolvents such as ethyl alcohol, ethanol General FAQssystem systems other than Windows USB monitor FAQs2012 Koninklijke Philips Electronics N.V. All rights reserved Specifications are subject to change without noticeVersion M3221SUE1T

Use the drop down list to select a display to be configured.