Manuals / Nokia / Computer Equipment / Network Router

Nokia M1112 Administrator Manual, Config mode level, Parameter, Setting, 192.168.1.1, 0.0.0.0

Models: M1112

1 109

Page 33

M1112 Administrator Manual

Config mode level	Parameter	Setting


system	hostname	M1112

eth	IP address	192.168.1.1
		255.255.255.0

vcc1	pvc	0 (vpi) 100 (vci)
		ppp-vc(encaps)

	IP address	0.0.0.0 0.0.0.0,
		means that M1112
		gets its IP address
		dynamically from the
		network.

	IP NAPT	on

	ppp authentication	both-chap-pap

	ppp username	none

	ppp password	none

common	ip route	0.0.0.0 0.0.0.0 0.0.0.0
		vcc1

	DHCP mode	server

Table 4-1M1112 default settings

4-2

E Copyright Nokia Networks Oy

C33907001SE_00

Page 33

Image 33

Nokia M1112 Administrator Manual, Config mode level, Parameter, Setting, 192.168.1.1, 255.255.255.0, 0.0.0.0, none

Contents

Nokia M1112 ADMINISTRATOR MANUALADSL over ISDN Router T66285M1112 Administrator Manual C33907.20 A0ADSL over ISDN Router E Copyright Nokia Networks OyE COPYRIGHT Nokia Networks Oy 2000 All rights reserved M1112 Administrator ManualDocument Document HistoryDate CommentM1112 Administrator Manual C33907001SE00E Copyright Nokia Networks Oy Applications and features ContentsChapter Introduction to Nokia M1112Installing Nokia M1112 Interfaces and indicator lightsManaging M1112 M1112 Administrator ManualTechnical specifications Appendix AGlossary viii M1112 Administrator ManualC33907001SE00 E Copyright Nokia Networks OyIntroduction to Nokia M1112 Chapter Introduction to Nokia M1112Your Nokia M1112 interconnects with a Digital Subscriber Line Access Multiplexer DSLAM installed and maintained by your access provider in their central office. M1112 ADSL technology is based on Discrete Multitone DMT modulation allowing a maximum of 8 Mbit/s data transmission from the network and 800 kbit/s towards the network. However, these figures illustrate the maximum performance of the technology and are subjected to the physical line conditions and the distance from you to the central office. M1112 is capable of adapting to the physical line conditions and guarantees the maximum transmission rate possible on the particular line. M1112 adapts its speed to the line conditions in steps of 32 kbit/s. In addition to these physical limitations affecting your data throughput, your Internet Service Provider ISP may limit your access according to their service provisioning policy and based on your service contract M1112 Administrator ManualChapter Applications and features Applications and features2.1 Applications Figure 2-1 High-speed Internet access M1112 Administrator ManualApplications and features Figure 2-2 Remote work using M1112 as a standard routerRemote work M1112 Administrator Manual 2.2 FeaturesLAN interconnection 2.2.1 InterfacesM1112 can operate in four different main modes D Bridging only Applications and featuresLAN interface M1112 Administrator ManualInternal host/gateway interface Applications and featuresData VCC operation 2.2.2 Routing2.2.4 Network Address Port Translation M1112 Administrator ManualApplications and features 2.2.5 Dynamic Host Configuration Protocol2.2.6 ATM and ADSL 2.2.7 Point-to-Point Tunneling Protocol PPTP M1112 Administrator Manual2.2.10 Weighted Fair Queueing Class of Service Applications and featuresFigure 2-5 Choosing the VCC2 for tunneling example 2.2.8 Point-to-Point Protocol over Ethernet PPPoEM1112 Administrator Manual 2.2.11 Management2.2.12 Dedicated management channel Figure 2-6 Dedicated management channel Applications and features2-14 M1112 Administrator ManualC33907001SE00 E Copyright Nokia Networks OyChapter Interfaces and indicator lights Interfaces and indicator lights3.1 Interfaces M1112 Administrator Manual 3.1.1 Ethernet interface3.1.2 ADSL interface Interfaces and indicator lights 3.2 Command line interfaceM1112 Administrator Manual 3.3 Indicator lightsInterfaces and indicator lights STA REDE Copyright Nokia Networks Oy M1112 Administrator Manual C33907001SE00E Copyright Nokia Networks Oy Chapter Installing Nokia M1112 4.1 M1112 default settingsInstalling Nokia M1112 Config mode level M1112 Administrator ManualSetting ParameterInstalling Nokia M1112 4.2 Step-by-step installation procedureM1112 Administrator Manual Chapter 5 Managing M1112 for instructions on how to configure M1112E Copyright Nokia Networks Oy Chapter Managing M1112 5.1 Operational examplesManaging M1112 Block diagram M1112 Administrator Manual5.1.1 Routing/tunneling IP only 5.1.2 Routing/tunneling IP, bridging other protocols5.1.3 Routing/tunneling IP, bridging all protocols including IP Managing M1112M1112 Administrator Manual 5.2 Typical configuration tasks5.2.1 Configuring DHCP and DNS 5.1.4 Bridging onlyManaging M1112 5.2.2 Configuring static and dynamic routing5.2.3 File system and downloading new firmware using TFTP M1112 Administrator ManualManaging M1112 Downloading configuration or application from monitorM1112 Administrator Manual 5.3 Browser managementserverfile= MONfile startup.cfg file size=556 MONwri startup.cfg Writing successful MON5.3.1 Opening a connection Managing M1112M1112 Administrator Manual 5.3.2 Main PageMain Page 5.3.3 Service Providers pages Figure 5-3 Service Providers page with PPP configurationManaging M1112 Figure 5-4 Service Providers page with PPTP configuration M1112 Administrator Manual5-12 E Copyright Nokia Networks Oy5.3.4 Local Network pages Managing M1112Local ports DHCPD Start address is the interface IP address D Subnet mask M1112 Administrator ManualFigure 5-6 Local Network DHCP page Managing M11125-15 E Copyright Nokia Networks OyNAPT M1112 Administrator ManualManaging M1112 Routing pageFigure 5-8 Local Network Routing page 5.3.5 Statistics page M1112 Administrator ManualStatistics page 5-18Managing M1112 On the Restart page, you can reset subsystems and restart M11125.3.6 Restart page Figure 5-10 Restart page5.4 Command line interface CLI M1112 Administrator Manual5.3.7 Save Config page Managing M1112 Local management console configurationThe configuration mode levels are D system D password D eth M1112 Administrator ManualCommand 5.4.1 Main mode commandsShow diagnostic log Managing M1112Command M1112 Administrator ManualCommand Show DSL line statusCommand CommandManaging M1112 Show ATM statusCommand M1112 Administrator ManualCommand CommandShow Address Resolution Protocol ARP table CommandCommand Managing M1112Command M1112 Administrator ManualCommand Show IP statisticsManaging M1112 CommandShow IP routing table 5-29Command M1112 Administrator ManualCommand Show Internet Control Message Protocol statisticsCommand CommandCommand Managing M1112Command M1112 Administrator ManualCommand CommandCommand CommandShow Dynamic Host Configuration Protocol server Managing M1112Command M1112 Administrator ManualShow M1112 information product-idShow running configuration CommandM1112 show config running system hostname M1112 eth Managing M1112Command M1112 Administrator ManualShow startup configuration CommandShow configuration file CommandCommand CommandCommand M1112 Administrator ManualCommand Switch off debugShow contents of file directory CommandCommand Managing M1112Command M1112 Administrator ManualCommand CommandExecute a command batch CommandCommand CommandCommand M1112 Administrator ManualSave configuration to file CommandReset subsystem CommandCommand CommandCommand M1112 Administrator ManualCommand Switch to configuration modeShow current running configuration Commandsystem password eth vcc1 ... vcc8 vbridge mngtvcc common Managing M1112Command M1112 Administrator ManualCommand Set configuration session timeoutCommand Password level commandAssign new password M1112 admin nokia M1112Command M1112 Administrator ManualSwitch on/off bridging CommandSwitch on/off RIP receive function in Ethernet inter CommandCommand Disable/enable management through the EthernetCommand M1112 Administrator ManualCommand Switch on/off bridgingSwitch on/off PPP authentication CommandCommand CommandCommand M1112 Administrator ManualStop PPP negotiation when authentication failure CommandSwitch on/off RIP receive function on ATM channel CommandCommand Enable Network Address Port TranslationCommand M1112 Administrator ManualCommand Disable/enable management through the ATM chanSwitch on/off IP function in vbridge CommandCommand Switch on/off RIP receive function in vbridgeCommand M1112 Administrator ManualSwitch on/off VCC-to-VCC bridging CommandSwitch on/off IP function on dedicated manage CommandCommand Switch on/off RIP receive function on dedicatedCommand M1112 Administrator ManualCommand Set max-config parameter valueCommand CommandSwitch on/off IP cache CommandCommand M1112 Administrator ManualCommand Switch on/off dynamic host configuration protocolCommand CommandManaging M1112 Set DHCP address rangeCommand M1112 Administrator ManualCommand CommandSwitch on/off weighted fair queueing CommandManaging M1112 M1112conf-common#misc global-wfq M1112conf-common#5-64 M1112 Administrator ManualC33907001SE00 E Copyright Nokia Networks OyTechnical specifications Appendix A Technical specificationsFeatures ADSL ATM over ADSLFeatures M1112 Administrator ManualCommand line interface CLI for local management Indicator lightsA.2 Ambient conditions, EMC and safety A.1 Mechanical construction and power supplyTechnical specifications Ambient conditionsSafety M1112 Administrator ManualSafetyEN60950 OvervoltageGlossary AbbreviationsGlossary command line interface ATM access networkTerms 10Base-T bridgeIntegrated services digital network Digital Subscriber Line Access Multiplexerencapsulation Ethernetmultiplexer remote access nodeserial console connection telecommuterGlossary web browserA software that is used to browse the World Wide Web Glossary-5M1112 Administrator Manual Glossary-6E Copyright Nokia Networks Oy

Config mode level

Parameter

Setting

M1112

192.168.1.1

255.255.255.0

0.0.0.0 0.0.0.0,

both-chap-pap

none

0.0.0.0 0.0.0.0 0.0.0.0

vcc1

server