Chapter Interfaces and indicator lights | Nokia M1112 instruction

Interfaces and indicator lights

Chapter 3

Interfaces and indicator lights

This chapter describes the external interfaces of M1112 and introduces its front panel indicator lights.

3.1Interfaces

M1112 has one ADSL line interface and one LAN interface (10Base-T Ethernet). It also has a local management interface (CLI) for management purposes. The ADSL line interface is compatible with ETSI TS 101 388 specification.

Power switch

Mains connector

Command line interface (CLI)

ADSL line (DSL)

Ethernet ports (ETH-1, ETH-2, ETH-3, ETH-4)

Figure 3-1M1112 back panel

C33907001SE_00

E Copyright Nokia Networks Oy

3-1

Image 26

Nokia M1112 manual Chapter Interfaces and indicator lights

Contents

Nokia M1112 M1112 M1112 Administrator Manual Document History Document Date Comment M1112 Administrator Manual Contents Chapter Interfaces and indicator lights Appendix a Technical specifications Viii Chapter Introduction to Nokia M1112 Nokia M1112 M1112 Administrator Manual Internet access Applications 1High-speed Internet access Remote work RAN L2TP Interfaces FeaturesLAN interconnection Route/tunnel IP only LAN interface Route/tunnel IP, bridge all other including IP Routing Internal host/gateway interfaceData VCC operation Bridging Network Address Port Translation Dynamic Host Configuration Protocol ATM and Adsl Point-to-Point Tunneling Protocol Pptp Payload encapsulations Weighted Fair Queueing Class of ServicePoint-to-Point Protocol over Ethernet PPPoE Management Dedicated management channel 6Dedicated management channel M1112 Administrator Manual Chapter Interfaces and indicator lights Interfaces Adsl interface Signal Direction MDI signalEthernet interface Ethernet Signal Direction MDI signal M5112-ter Minal Command line interfaceSignal Indicator lights 5M1112 front panel indicators Off Hardware malfunction during startup M1112 Administrator Manual Chapter Installing Nokia M1112 M1112 default settings 192.168.1.1 Config mode level Parameter SettingM1112 255.255.255.0 Step-by-step installation procedure Managing M1112 for instructions on how to configure M1112 Chapter Managing M1112 Operational examples Routing/tunneling IP, bridging other protocols Block diagramRouting/tunneling IP only Routing/tunneling IP, bridging all protocols including IP Bridging only Typical configuration tasksConfiguring Dhcp and DNS Configuring static and dynamic routing File system and downloading new firmware using Tftp Use CLI to issue Downloading configuration or application from monitor Browser management Opening a connection Main Service Providers pages 3Service Providers page with PPP configuration 4Service Providers page with Pptp configuration Local Network pages Local ports M1112 Administrator Manual 6Local Network Dhcp Napt 8Local Network Routing Statistics Restart 10 Restart Command line interface CLI Save Config Setting Value M1112 Administrator Manual Main mode commands Command Show diagnostic log Command Show DSL line status Command Show Ethernet interface status Managing M1112 Command Show ATM statusCommand Show bridge interface status Command Show Pptp information Command Show bridging statisticsCommand Show bridging table Command Show Address Resolution Protocol ARP table Command Show IP interfaces Command Show IP statistics Command Show IP cache table and statistics Command Show IP routing table Vbridge Command Show Internet Control Message Protocol statistics Command Show User Datagram Protocol statistics Command Show Snmp statistics Command Show Transmission Control statisticsCommand Show Routing Information Protocol statistics VCC3 Command Show Domain Name Server entry table and statis Tics Command Show M1112 information Command Show running configuration Command Show startup configuration Command Show default configuration Command Ping Command Show configuration fileCommand Show debug status Command ATMping Command Switch off debug Command Show contents of file directory Command Copy file Command Download new firmware Command Rename fileCommand Delete file Command Save log to a default file Command Execute a command batchCommand Save log to file Command Clear counters Command Save configuration to fileCommand Restore configuration Command Fast restart M1112 Command Reset subsystemCommand Logout Command Switch to configuration mode Configuration mode commandsCommand Restart M1112 Command Return to root level Root level commands Command Show current running configuration Command Set configuration session timeout System level commandsCommand Assign hostname Password level command Command Assign new password Command Switch on/off IP function in Ethernet interface Ethernet level commandsCommand Switch on/off bridging M1112conf-eth#ip rip-receive VCC ATM channel commands Command Activate ATM channel Command Set PPP password Command Switch on/off PPP authenticationCommand Set PPP username Command Switch on/off IP function on ATM channel Command Switch on/off RIP send function on ATM channel Command Switch on/off RIP receive function on ATM channel Command Enable Network Address Port Translation Command Set server support entry Command Disable/enable management through the ATM chan Nel Command Switch on/off RIP receive function in vbridge Vbridge commandsCommand Switch on/off IP function in vbridge Command Disable/enable management through the vbridge Command Activate dedicated management channel Dedicated management channel commandsCommand Switch on/off VCC-to-VCC bridging Common commands Command Set PPP packet size Command Set max-terminate parameter value Command Set PPP restart time parameterCommand Set max-config parameter value Command Add/delete IP route Command Set max-failure parameter valueCommand Switch on/off IP cache Command Define and activate host acces list Command Switch on/off dynamic host configuration protocol Command Set Dhcp address range Command Set DNS address for Dhcp clients Command Set Domain name server address Command Set Dhcp server lease timeCommand Set Dhcp pool domain name Command Switch on/off weighted fair queueing M1112 Administrator Manual Ethernet interface FeaturesATM over Adsl Routing Dedicated ATM management channel Command line interface CLI for local managementIndicator lights Management through payload Ambient conditions Mechanical construction and power supplyAmbient conditions, EMC and safety Mechanical construction Safety Digital Subscriber Line Access Multiplexer Asynchronous transfer modeCommand line interface Intergrated services digital network Terms 10Base-T Encapsulation Multiplexer Web browser Glossary-6