Safety | Nokia M1112 specs

M1112 Administrator Manual

Overvoltage

ITU-T K.21

Safety

SafetyEN60950

A-4

E Copyright Nokia Networks Oy

C33907001SE_00

Image 103

Nokia M1112 manual Safety

Contents

Nokia M1112 M1112 M1112 Administrator Manual Document Date Comment Document History M1112 Administrator Manual Contents Chapter Interfaces and indicator lights Appendix a Technical specifications Viii Nokia M1112 Chapter Introduction to Nokia M1112 M1112 Administrator Manual Applications Internet access 1High-speed Internet access RAN L2TP Remote work LAN interconnection FeaturesInterfaces Route/tunnel IP only Route/tunnel IP, bridge all other including IP LAN interface Bridging Internal host/gateway interfaceData VCC operation Routing Network Address Port Translation ATM and Adsl Dynamic Host Configuration Protocol Point-to-Point Tunneling Protocol Pptp Point-to-Point Protocol over Ethernet PPPoE Weighted Fair Queueing Class of ServicePayload encapsulations Dedicated management channel Management 6Dedicated management channel M1112 Administrator Manual Interfaces Chapter Interfaces and indicator lights Ethernet Signal Direction MDI signalEthernet interface Adsl interface Signal Command line interfaceSignal Direction MDI signal M5112-ter Minal 5M1112 front panel indicators Indicator lights Off Hardware malfunction during startup M1112 Administrator Manual M1112 default settings Chapter Installing Nokia M1112 255.255.255.0 Config mode level Parameter SettingM1112 192.168.1.1 Step-by-step installation procedure Managing M1112 for instructions on how to configure M1112 Operational examples Chapter Managing M1112 Routing/tunneling IP only Block diagramRouting/tunneling IP, bridging other protocols Routing/tunneling IP, bridging all protocols including IP Configuring Dhcp and DNS Typical configuration tasksBridging only Configuring static and dynamic routing File system and downloading new firmware using Tftp Downloading configuration or application from monitor Use CLI to issue Browser management Opening a connection Main 3Service Providers page with PPP configuration Service Providers pages 4Service Providers page with Pptp configuration Local ports Local Network pages M1112 Administrator Manual 6Local Network Dhcp Napt 8Local Network Routing Statistics 10 Restart Restart Save Config Command line interface CLI Setting Value M1112 Administrator Manual Command Show diagnostic log Main mode commands Command Show Ethernet interface status Command Show DSL line status Command Show bridge interface status Command Show ATM statusManaging M1112 Command Show bridging table Command Show bridging statisticsCommand Show Pptp information Command Show IP interfaces Command Show Address Resolution Protocol ARP table Command Show IP cache table and statistics Command Show IP statistics Vbridge Command Show IP routing table Command Show User Datagram Protocol statistics Command Show Internet Control Message Protocol statistics Command Show Routing Information Protocol statistics Command Show Transmission Control statisticsCommand Show Snmp statistics VCC3 Command Show Domain Name Server entry table and statis Tics Command Show M1112 information Command Show running configuration Command Show default configuration Command Show startup configuration Command Show debug status Command Show configuration fileCommand Ping Command Switch off debug Command ATMping Command Copy file Command Show contents of file directory Command Delete file Command Rename fileCommand Download new firmware Command Save log to file Command Execute a command batchCommand Save log to a default file Command Restore configuration Command Save configuration to fileCommand Clear counters Command Logout Command Reset subsystemCommand Fast restart M1112 Command Return to root level Configuration mode commandsCommand Restart M1112 Command Switch to configuration mode Command Show current running configuration Root level commands Command Assign hostname System level commandsCommand Set configuration session timeout Command Assign new password Password level command Command Switch on/off bridging Ethernet level commandsCommand Switch on/off IP function in Ethernet interface M1112conf-eth#ip rip-receive Command Activate ATM channel VCC ATM channel commands Command Set PPP username Command Switch on/off PPP authenticationCommand Set PPP password Command Switch on/off RIP send function on ATM channel Command Switch on/off IP function on ATM channel Command Enable Network Address Port Translation Command Switch on/off RIP receive function on ATM channel Command Disable/enable management through the ATM chan Nel Command Set server support entry Command Disable/enable management through the vbridge Vbridge commandsCommand Switch on/off IP function in vbridge Command Switch on/off RIP receive function in vbridge Command Switch on/off VCC-to-VCC bridging Dedicated management channel commandsCommand Activate dedicated management channel Command Set PPP packet size Common commands Command Set max-config parameter value Command Set PPP restart time parameterCommand Set max-terminate parameter value Command Switch on/off IP cache Command Set max-failure parameter valueCommand Add/delete IP route Command Switch on/off dynamic host configuration protocol Command Define and activate host acces list Command Set DNS address for Dhcp clients Command Set Dhcp address range Command Set Dhcp pool domain name Command Set Dhcp server lease timeCommand Set Domain name server address Command Switch on/off weighted fair queueing M1112 Administrator Manual Routing FeaturesATM over Adsl Ethernet interface Management through payload Command line interface CLI for local managementIndicator lights Dedicated ATM management channel Mechanical construction Mechanical construction and power supplyAmbient conditions, EMC and safety Ambient conditions Safety Intergrated services digital network Asynchronous transfer modeCommand line interface Digital Subscriber Line Access Multiplexer Terms 10Base-T Encapsulation Multiplexer Web browser Glossary-6