
Adjusting the position
ASPECT
Refer page 30.
matched to the input signal and are automatically adjusted.
When the input signal is from a PC, first select AUTO SETUP and then press the ENTER button to initiate automatic positioning.
If the optimum setting is not obtained when AUTO SETUP is carried out, adjust by the following
VERTICAL POSITION
DOT CLOCK
AUTO SETUP
(PC only)
HORIZONTAL POSITION, VERTICAL POSITION, DOT CLOCK and CLOCK PHASE are
NOTE:
BWhen the ASPECT is set to V- SCROLL (page 30), AUTO SETUP cannot be performed.
procedure.
Use the F and G buttons to select an item, and then use the I and H buttons to change the setting for that item.
For items with bar scales, press the ENTER button or the I or H buttons to display the adjustment screen, and then use the I or H buttons to make the adjustment.
When an
YPBPR /DVI signal is being input or SD CARD is selected.
POSITION |
|
H - POSITION | 0 |
|
|
V - POSITION | 0 |
ASPECT | 16:9 |
SELECT ENTER | ESC |
B“ASPECT” can be adjusted only when a DVI signal is being input or when “SD CARD” is selected.
When an PC signal is being input
POSITION
H - POSITION 0
V - POSITION | 0 |
DOT CLOCK | 0 |
|
|
CLOCK PHASE | 0 |
|
|
ASPECT | 4:3 |
AUTO SETUP |
|
SELECT ENTER | ESC |
(PC only)
Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is
projected. If this happens, use the
Iand H buttons to adjust so that any such noise is minimised.
CLOCK PHASE
(PC only)
Adjust the DOT CLOCK setting first before carrying out this adjustment. Use the I and H buttons to adjust so that the noise level is least noticeable.
NOTE:
BIf signals with a dot clock frequency of 100 MHz or higher are being input, interference may not be completely eliminated when the DOT CLOCK and CLOCK PHASE adjustments are carried out.
Option settings
Use the F and G buttons to select an item, then press the I or H buttons to change the setting.
|
| OPTION |
| |
OSD |
|
|
| ON |
|
|
|
|
|
NR |
|
|
| ON |
|
|
|
| |
PC PRIORITY | NORMAL | |||
|
|
|
|
|
BACK | COLOR | BLACK | ||
|
|
|
|
|
4:3 | H - POS | CENTER | ||
|
|
|
| |
FRONT/REAR | FRONT | |||
�DESK/CEILING | DESK | |||
FAN | CONTROL | NORMAL | ||
|
|
|
|
|
LAMP | POWER | HIGH | ||
|
|
|
|
|
LAMP | RUNTIME | 5H | ||
S E L E C T |
| ADJ | ESC | |
| ||||
|
|
|
|
|
OSD
OSD |
| ON |
|
| [ |
| |
|
| OFF |
|
ON | The signal name is | ||
| displayed in the | ||
| corner of the screen when | ||
| the input signal is | ||
| changed. | ||
OFF | Use this setting when you | ||
| do not want the signal | ||
| name to be displayed. |
NR (Noise Reduction)
Reduction) feature, set it to “OFF”.
PC PRIORITY |
|
|
| Operation | |||
|
|
|
| ||||
(PC only) |
|
|
|
| |||
|
|
|
| ||||
PC PRIORITY | NORMAL |
|
| ||||
|
|
| [ |
|
|
| |
|
|
| WIDE |
|
| ||
NORMAL displays the PC screen | Basic | ||||||
| |||||||
data in a 4:3 aspect ratio. |
| ||||||
WIDE displays the PC screen data |
| ||||||
in a 16:9 aspect ratio. |
| ||||||
BACK COLOR |
|
|
| Operation | |||
|
|
|
|
|
| ||
BACK COLOR | BLACK |
|
| ||||
|
|
| [ |
|
|
| |
|
|
| BLUE |
|
|
| |
This sets the color which is |
| ||||||
projected onto the screen when no | Advanced | ||||||
signal is being input to the projector. | |||||||
|
This sets the background color for the left/right margins when the 4:3 aspect ratio is selected. (Refer to page 31.)
HORIZONTAL POSITION
NR | ON |
| [ |
| OFF |
If noise occurs from the projector because of a poor input signal, set NR to “ON”.
To turn off the NR (Noise