Philips PXG20 manual Operation, Preparation, Remarks, Using the Remote Control

Page 17

8. OPERATION

Preparation

 

 

PREPARATION

Turning on/off the power

1.Make the necessary connections before proceeding. Connect the powercord to a wall outlet.

The Power indicator lights up red and the projector enters standby mode.

2.Press Power ON.

The power indicator lights up green and the flashing green Lamp indicator shows that the lamp is warming up. Wait until the indicator stops flashing before operating the projector.

If the power is turned off and then immediately turned on again, it may take a short while before the lamp turns on.

Notes:

If the bottom filter cover is not securely installed, the Power indicator flashes in red.

After the projector is unpacked and turned on for the first time, a slight odour may be emitted from the exhaust vent. This odour will soon disappear with use.

Remarks:

1) When the power is on, the Lamp indicator (Lamp) indicates

the status of the lamp.

Notes:

Wait until the cooling fan stops (about 2 minutes after the projector has been switched off) before disconnecting the powercord.

The power can be turned on again by pressing Power ON. When the power is turned on, the Power indicator and the Lamp indicator light green.

USING THE REMOTE CONTROL

(fig. 2)

The remote control has the following two functions:

Projector control

Wireless mouse

Slide the remote control power ON/OFF switch into the ON

position for switching the projector and the Remote Control unit to on.

The remote control can be used to control the projector within the ranges shown below.

The USB mouse receiver can be used with the remote control to control the mouse functions of a connected computer within the ranges shown below.

Green: lamp is ready.

Flashing green: warming up.

Red: change the lamp.

2) After the picture is displaying, the warming-up indicator

‘WARMING UP, PLEASE WAIT’ is shown

3.Press the button of the desired input mode, Data 1, Data 2, Video.

On the remote control press the Input button to select the desired input mode (Data 1, Data 2, Video).

Press Input again to change the mode. Example:

DATA

 

DATA

7m (23'8)

30˚

 

30˚

45˚

 

45˚

30˚

When no signal is being received, ‘NO SIGNAL’ will be displayed. When a signal that the projector is not preset to receive is being received, ‘NOT REG.’ will be displayed.

4.Press Volume to adjust the volume. (on the local keyboard only)

5.Press A/V Mute to temporarily turn off the sound and picture.

Press A/V Mute again to turn the sound and picture back on.

6.Press Standby/OFF for switching off the projector.

4m (13'8)

45˚

 

 

30˚

Using the remote control in a dark room

Press BACKLIGHT, and the buttons will light up.

Notes:

Be sure the supplied USB mouse receiver is connected to your computer.

The wireless mouse may not operate correctly if your computer serial port is not correctly set up. Refer to the computer’s operation manual for details of setting up/installing the mouse driver.

For one-button mouse systems, use either the LEFT-CLICK or RIGHT-CLICK button.

15

Image 17
Contents User guide Important Note for Users in the U.S.A Reference Important SafeguardsIntroduction FCC Warning Things YOU should KnowComputer RGB / Component inputs Advanced Compatibility with HIGH-END Workstations and PC’s Projector FeaturesLamp Monitor Function Temperature Monitor FunctionSee illustrations on Functional OverviewControls On projector figRemote Control Connections Power Supply SET UPUsing the adjustment feet Positioning the Projector and ScreenMoving the Projector Lens AdjustmentInserting the Batteries in the Remote Control VIDEO/COMPUTER Cables and Adapter InstallationVideo/computer cables and adapter General Connecting to a computerConnecting to a Computer Connecting to Video Equipment Connecting to video equipmentEquipped with a Scart connector Case your VCR, Laser Disc player, video camera or TV isConnecting the Remote Control Mouse Receiver Connecting to audio equipment/remote control mouse receiverConnecting to Audio Equipment Operation Using the Remote ControlPreparation PreparationVideo Mode Menu Control Data Mode Menu ControlGraphical User Interface Graphical User InterfaceVideo Mode Input Signal Data Mode Input SignalPicture control Picture ControlData display Fine Sync adjustments Data Mode DisplayDescription of Adjustment Items Auto Sync AdjustmentPicture adjustments Data Mode / Video Mode DisplayColor Temperature adjustments Auto Sync Display FunctionProgressive mode Interlaced modePicture control/Audio control Audio ControlSelecting a saved setting Saving/changing the adjustment settingPersonal preferences Personal PreferencesCeiling-mount Setup Other SettingsREVERSE/INVERT Image Function Digital Freeze Function D-FREEZEEffect Modes Video Mode Picture display mode Format on projector keyboard onlyData Mode Setting the Password Checking the Input Signal Changing the PasswordSetting a Background Image Selecting the Keylock LevelStatus Function Selecting a Startup ImageMenu Tree Data Mode Video Mode Main MenuCleaning and replacing the bottom air filter Connecting RS-232C port/MaintenanceCleaning the side air filter not removable Lamp/Maintenance IndicatorsMaintenance Indicator Condition Problem Possible Solution MaintenanceLamp LCA 3112 8670 931 Replacing the lampKensington Lock Resetting the lamp timerTroubleshooting