dbx Pro 386 user manual Declaration Conformity

Page 3

IMPORTANT SAFETY INSTRUCTIONS

LITHIUM BATTERY

WARNING

CAUTION!

This product may contain a lithium battery.There is danger of explosion if the battery is incorrectly replaced. Replace only with an Eveready CR 2032 or equivalent. Make sure the bat- tery is installed with the correct polarity. Discard used batter- ies according to manufacturer’s instructions.

ADVARSEL!

Lithiumbatteri - Eksplosjonsfare.Ved utskifting benyttes kun batteri som anbefalt av apparatfabrikanten. Brukt batteri returneres apparatleverandøren.

ADVARSEL!

Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri av samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren.

VAROITUS!

Paristo voi räjähtää, jos se on virheellisesti asennettu.Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

VARNING!

Explosionsfara vid felaktigt batteribyte. Använd samma batteri- typ eller en ekvivalent typ som rekommenderas av apparattil- lverkaren. Kassera använt batteri enligt fabrikantens instruk- tion.

ELECTROMAGNETIC

COMPATIBILITY

This unit conforms to the Product Specifications noted on the Declaration of Conformity. Operation is subject to the following two condi- tions:

this device may not cause harmful inter- ference, and

this device must accept any interference received, including interference that may cause undesired operation.

Operation of this unit within significant electro- magnetic fields should be avoided.

U.K. MAINS PLUG WARNING

A molded mains plug that has been cut off from the cord is unsafe. Discard the mains plug at a suitable disposal facility. NEVER UNDER

ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A 13 AMP POWER SOCKET. Do not use the mains plug without the fuse cover in place. Replacement fuse covers can be obtained from your local retailer. Replacement fuses are 13 amps and MUST be ASTA approved to BS1362.

DECLARATION OF

CONFORMITY

Manufacturer’s Name:

dbx Professional Products

Manufacturer’s Address:

8760 S. Sandy Parkway

 

Sandy, Utah 84070, USA

declares that the product:

 

Product name: dbx 386

Product option: N/A

conforms to the following Product Specifications:

EMC: EN 55013 (1990)

EN 55020 (1991)

Supplementary Information:

The product herewith complies with the require- ments of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC as amended by Directive 93/68/EEC.

dbx Professional Products Vice-President of Engineering 8760 S. Sandy Parkway Sandy, Utah 84070, USA December 15, 1999

European Contact: Your Local dbx Sales and Service Office or

Harman Music Group

8760 South Sandy Parkway

Sandy, Utah

84070 USA

(801)568-7638

(801)568-7642

Image 3
Contents 386 Important Safety Instructions Declaration Conformity 386 Table of ContentsIntro Defining IntroductionWarranty Introduction Service Contact InfoInstallation Recommendations Getting Getting Started Rear Panel Connections IEC Power Cord ReceptacleFront Panel Controls Getting StartedFront Panel Type IV conversion system controls Meter Select SwitchAnalog Analog Applications Basic Analog ConnectionConnection to a Mixing Console Direct Connection to a Recorder Page Digital Digital Output Rear Panel Connections Digital Applications Digital Output Front FunctionsSync Input Sample Rate Selection Digital ApplicationsRear Panel Connections Direct Connection to a DAW CPUDirect Connection to a Digital Mixer SectionDigital Applications A/D Conversion Multi-Tracking to Digital Digital Applications Analog and Digital Output Application Appendix Fig. A.1 Sync Input InfoBlock Block DiagramType IV White Paper By Roger JohnsonAppendix C Appendix C Appendix C Appendix C Truncation AppendixAppendix D Harman International Company