Appendix D | Appendix |
| 386 | |||
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| D.3 Specifications |
|
|
|
| |
Microphone Input |
|
|
|
| ||
Connector: |
|
| Female XLR Pin 2 Hot | |||
Type: |
|
| Electronically balanced/unbalanced | |||
Impedance: |
|
| 330Ω |
| ||
Maximum Input Level: |
|
| ||||
CMRR: |
|
| >40dB, Typically 55dB | |||
Equivalent Input Noise: |
|
| Typically | |||
Line Input (Rear Panel) |
|
|
|
| ||
Connector: |
|
| TRS 1/4" Jack | |||
Type: |
|
| Electronically balanced/unbalanced | |||
Impedance: |
|
| 20kΩ unbalanced, 40kΩ balanced | |||
Maximum Input Level: |
|
| +21dBu balanced or unbalanced | |||
CMRR: |
|
| >40dB, Typically 55dB | |||
Gain (Drive Control) |
|
| ||||
Instrument Input (Front Panel) |
|
| ||||
Connector: |
|
| TS 1/4" Jack | |||
Type: |
|
| Unbalanced | |||
Impedance: |
|
| 470 kΩ | |||
Maximum Input Level: |
|
| +21dBu unbalanced | |||
Analog Outputs |
|
|
|
| ||
Connector: |
|
| Male XLR Pin 2 Hot and TRS 1/4" | |||
Type: |
|
| ||||
Impedance: |
|
| Balanced 120Ω , unbalanced 60Ω | |||
Maximum Output Level: |
|
| >+21 dBu, >+20 dBm (into a 600Ω load) | |||
Insert |
|
|
|
| ||
Connector: |
|
| TRS 1/4" | |||
Type: |
|
| Unbalanced | |||
Impedance: |
|
| 100Ω | (SEND), 20kΩ (RETURN) | ||
Digital Outputs |
|
|
|
| ||
Connectors: |
|
| XLR for AES/EBU | |||
|
|
|
|
| RCA for S/PDIF | |
Impedance: |
|
| 110Ω | for AES/EBU | ||
|
|
|
|
| 75Ω | for S/PDIF |
Word Sync Input/Output |
|
|
|
| ||
Connectors: |
|
| BNC |
| ||
Input Impedance: |
|
| 75Ω terminated by internal jumper | |||
Input: |
|
| 96, 88.2, 48, or 44.1kHz word clock | |||
Output: |
|
| 96, 88.2, 48, or 44.1kHz word clock | |||
System Performance |
|
|
|
| ||
DRIVE Control Range: |
|
| +30dB to +60dB for Mic Input | |||
LEVEL Control Range |
|
| ||||
|
|
|
| |||
(Analog and Digital): |
|
| ||||
LINE: |
|
| Selects between microphone and line inputs | |||
Phantom Power: |
|
| +48V | |||
PAD: |
|
| 20dB pad | |||
PHASE: |
|
| Reverses pins 2 and 3 of the microphone input XLR | |||
LOW CUT: |
|
| 75Hz, 12dB/octave high pass filter | |||
Analog Frequency Response: |
|
|
| <10Hz to 75kHz | ||
THD+Noise: |
|
| 0.35% typical at +4dBu out, 1kHz, 40 dB gain | |||
Interchannel Crosstalk: |
|
| Typically | |||
Analog to Digital Conversion |
|
| ||||
Type: |
|
| dbx Type IV™ A/D Conversion System | |||
Sample Rate: |
|
| 96, 88.2, 48, or 44.1kHz selectable | |||
Wordlength: |
|
| 24, 20, or 16 bit selectable | |||
Dither Type: |
|
| TPDF, SNR2, or none | |||
Noise Shape: |
|
| Shape 1, Shape 2, or none | |||
Output Format: |
|
| S/PDIF or AES/EBU | |||
Convertor Dynamic Range |
|
| 107dB typical, | |||
Power Supply |
|
|
|
| ||
Operating Voltage: |
|
| DO: 120VAC 60Hz, 100VAC 50/60Hz | |||
Power Requirements: |
|
| EU: 230VAC 50/60 Hz | |||
|
| 35 Watts | ||||
Physical |
|
|
|
| ||
Weight: |
|
| 7.3 lbs (3.3kg) | |||
Dimensions: |
|
| 1.75'' x 7.75'' x 19'' (4.5cm x 19.7cm x 48.5cm) | |||
NOTE: 0dBu=
®
26 | 386 User Manual |
|
|