Philips P88 manual Playing a CD, Disc Change, Selecting a desired track, Programming Tracks

Page 18

 

CD

 

 

English

Playing a CD

1 Press PLAYĥto start playback.

 

ª The disc tray, track number and

 

elapsed playing time of the current

 

track appear on the display.

•To interrupt playback, press PAUSEƒ•.

ª The playing time flashes.

•To resume playback, press PLAYƒ• again.

2To stop playback, press ‚.

Notes:

–All the available discs will play once, then stop.

–When the CD has stopped playing, the system will switch to standby mode after 30 minutes if no button is pressed.

18

Disc Change

You can change the outer two discs while the third inner disc is stopped or is playing.

1Press DISC CHANGE.

ª The CD carousel tray slides out.

2Replace the discs in the left and right disc trays.

•If you wish to change the inner disc during playback, press DISC CHANGE again.

ª"DISC CHANGE" will be displayed.

ªThe CD will stop playing.

ªThe CD carousel tray will close to

retrieve the inner CD and then open again with the inner CD accessible.

3Press OPEN•CLOSE to close the CD carousel tray.

Selecting a desired track

Selecting a desired track when playback is stopped

1Press ’or ‘(or Digit 0-9on the remote control) until the desired track appears on the display.

2Press PLAYĥ to start playback.

ªThe selected track number and elapsed playing time appear on the display.

Selecting a desired track during playback

•Press ’or ‘(or Digit 0-9on the remote control) until the desired track appears on the display.

ªThe selected track number and elapsed playing time appear on the display.

•If you press ’once it will skip to the beginning of the current track and play the track again.

Note:

–Pressing’during shuffling can only skip to the beginning of the current track.

Searching for a particular passage during playback

•Press and hold ˆor ‡until the desired passage is located.

ª The volume will be reduced.

•Play returns to normal when ˆor ‡ is released.

Programming Tracks

Programming tracks of a loaded CD is possible when playback is stopped. The display will indicate the total tracks stored in the program. Up to 40 tracks can be stored in the memory in any order. When 40 tracks are stored and you attempt to store another track, the display will show “PROGRAM FULL”.

1Load the desired discs in the disc trays.

2Press PROG to start programming.

ªThe PROGRAM starts flashing.

ªIt will cancel any previously selected repeat mode.

3Press the CD (CD 1•2•3) or DISC 1/2/3 button to select the disc.

4Press ’or ‘(or Digit 0-9 on the remote control) to select the desired track.

5Press PROG to store the track.

•Repeat steps 3 to 5 to store other discs and tracks.

6Press ‚once to end programming.

ªThe total number of tracks programmed and total playing time appear on the display.

Notes:

–If the total playing time is more than

“99:59“ or if one of the programmed tracks has a number greater than 30, then “--:--” appears on the display instead of the total playing time.

pg 01-31/P88/22-Eng

18

3/6/00, 1:26 PM

3139 116 19721

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Mini Hi-Fi System 3139 116Mains plug How to connect a plugImportant notes for users in the U.K Copyright in the U.KSvenska English Français Español Deutsch NederlandsItaliano DanskContents General Information Accessories SuppliedSafety Information Environmental InformationAM Loop Antenna Connection FM Wire Antenna ConnectionPreparation Speakers ConnectionAC Power Supply Connecting other Equipment to your systemWireless Surround Out Connection Inserting batteries into the Remote ControlDolby Pro Logic Setting up the Dolby Pro Logic systemDolby PRO Logic Test ToneDolby Center Phantom Dolby SurroundDolby 3 Stereo Normal StereoControls DiscControls on the system and remote control ’, ‘, etc Easy Set Demonstration modeTo stop the demonstration mode ModeVolume Control Switching the system onSwitching the system to standby mode Dim modeWOOx level cannot be stored as part of the personal setting Personal SettingTo exit without storing the setting, press ‚ Denotes the sound levelWOOx There are three wOOx settings to enhance the bass responseWhen normal wOOx sound effect is selected Automatic DSC-wOOx / VEC-wOOx selectionDiscs for playback CD TextLoading the CD Changer CD Direct PlaySelecting a desired track Playing a CDDisc Change Programming TracksReviewing the program Playing the programErasing the program when Tuning to Preset Radio Stations Tuning to radio stationsStoring Preset Stations TunerNEWS/TA Traffic Announcement Receiving RDS Radio StationOnly available in Radio Station with RDS Selecting External Equipment There are two Auxiliary modes Normal AUX modeTuner AUX/CDR During News bulletin or TrafficTape Playback TapeLoading a tape Auto Reverse Playback only onDolby B Noise Reduction System When playback is stoppedRewind/Fast Forward 3afor playback on tape deck 2 onlyRecording Recording from other sourcesOne Touch Recording Only Œ mode is available during dubbingCD Synchro Start Recording Digital Recording via Digital OutClock Timer SettingClock Setting View ClockTo switch off the Timer TimerSleep Timer To switch off the Sleep TimerSpecifications Subject to modificationCD Player Operation Maintenance TroubleshootingMaintenance Radio ReceptionTape Deck Operation General
Top Page Image Contents