TRENDnet TEW-310APBX manual Setting Up an Infrastructure Network

Page 12

Setting Up an Infrastructure Network

Setting Up an Infrastructure Network

Please remember that TRENDware wireless devices are pre-configured to connect together, right out of the box, with the default settings.

1

2 3

You will need a broadband Internet access (Cable/DSL) subscription.

Consult with your Cable/DSL provider for proper installation of the modem.

Configure TEW-310APB.Refer to the Quick Installation Guide for

setting up the Access Point.

Note: If you already have a DHCP server (e.g. Internet Router) on the network, please disable the DHCP Server function on the TEW-310APB.

4

5

If you are connecting a desktop computer in your network, you can install the TRENDnet TEW-303PIwireless PCI adapter into

an available PCI slot. See the Quick Installation Guide included

with the TEW-303PI

If you are connecting a Notebook computer in the network, install the drivers for the TEW-301PC wireless CardBus adapter into the laptop computer. See the Quick Installation Guide included with

TEW-301PI for installation instructions.

6 After the configuration, connect the Access Point to your network. If you have an Internet Router, connect it to the cable/DSL

Please refer to the following sections of this manual for additional information about setting up a network:

Networking Basics- learn how to check your IP Address; share printers and files.

Using the Configuration Utility-

learn the settings you must use on each computer in your network for successful communication.

Fig. 4.1

Troubleshooting learn how to check for the proper installation of the network adapters' drivers and other tips for troubleshooting the network.

11

Image 12

Contents 2.4 GHz Wireless Access Point + Bridge TEW-310APB TEW-310APBXUsers Guide CONTENTS 1.Package Contents3.Wireless Basics 5.Using the Configuration UtilityReplacing the antenna with high gain antenna 2 Locate antenna connectors1 Locate the two antennas inside the box1. Package Contents ContentsSystem Requirements If any of the above items are missing, please contact your reseller2. Introduction ConnectionsFeatures and Benefits LED Indicators 3. Wireless Basics TRENDware Wireless Family of LAN products include Installation ConsiderationsStandards - Based Technology objects that the wireless signal must pass thru may limit range. Typical ranges vary depending on the types of materials and any background RF radio frequency noise in your home or business. The key to maximizing range is to follow these basic guidelines 4. Getting Started please remember that the IP Address for each computer must be inIP ADDRESS Setting Up an Infrastructure Network 5. Using the Configuration Menu Factory Default Setting for the TEW-310APBConfiguration Menu Status Screen with Menu Bar Basic Settings AP name SSID Channel WEP Key ModeIP Settings Automatically . Or you canSubnet Mask , and Gateway by Advanced Settings AP ModeAuthentication Type Security 802.1XNote Please do not interrupt the firmware upgrade process Tools6. Troubleshooting Based on Windows XP Operating SystemGateway Address ∙ Click Properties ∙ Select the Hardware Tab ∙ Click Device ManagerAdapters Cardbus Adapter∙ Right-click on 22M Wireless ∙ Select Properties to check that the drivers are installed properly4. Resetting the TEW-310APB to Factory Default Settings Using the Network Setup Wizard in Windows XP Select Set up a home or small office network7. Networking Basics Microsoft Windows XP Go to Start Control Panel Network ConnectionsPlease follow all the instructions in this window Click NextEnter a Computer description and a Computer name Workgroup nameClick Next Note Each computer should have a unique Computer name When the changes are complete, click Next Please wait while the wizard applies the changesInsert a disk into the Floppy Disk Drive, in this case drive A Format the disk if you wish, and click NextPlease wait while the wizard copies the files Page Naming your Computer In Windows XPGo to Start All Programs Accessories Command Prompt Checking the IP Address in Windows XP/2000Type Command and click OK AddressAssigning a Static IP Address Control PanelNetwork Connections Connections ∙ Click Properties ∙ Right-click on Local Area∙ Highlight Internet Protocol TCP/IP ∙ Input your DNS server address only if you plan to use the Internet You have completed the assignment of a Static IP AddressConnecting to a Wireless Network in Windows XP Network ConnectionInternet Protocol TCP/IP click Properties ∙ Select Obtain an IP addressConnecting to a Wireless Network in Windows ∙ IP address ∙ Subnet maskProperties select Internet Protocol TCP/IP click Properties Connecting to a Wireless Network with a Wireless Router or an Access Point using a DHCP server in Windows Connecting to a Wireless Network in Windows Me and ∙ Go to Start Settings Control Panel Double-clickselect Internet Protocol TCP/IP click Properties ∙ Select Detect connection to network mediaChecking the Wireless Connection by Pinging ∙ Select Specify an IP addressFor Windows XP and For Windows Me and Shared Documents folder and Sharing files and folders in the Help andFile and Printer Sharing 8. Technical Specifications Diagnostic LEDStandards PortsDimensions WeightTemperature Humidity9. Contacting Technical Support TRENDware Technical Support over the Telephone Tel +1-310-891-1100TRENDware Technical Support E-mailAddress E-mail support@trendware.com