TRENDnet TEW-310APBX manual Security, 802.1X

Page 19
Security

Security

Password: Change the login User

Name and Password in this screen.

Administrator ID: This is the login User Name for the browser configuration. Default is admin, you can enter a name with up to 15 characters.

AP Password New: Enter the new password (up to 15 characters).

Fig. 5.7

Confirm: Enter the new password again.

Click Apply to save the new User Name and Password.

Click Cancel to discard the changes.

MAC Filter: Use MAC Filters to allow or deny wireless connection to the TEW-310APB. Select Enable to activate the filter, select Disable (default) to disable this feature.

Select Only deny PCs with the MAC listed below to access the device or select Only allow PCs with the MAC listed below to access the device and enter the MAC Address of the selected computers into the fields below.

You could enter up to 50 MAC address entries, but only 10 entries are displayed. Please click on the 1~10 pull-down arrow and select the next 10 entries (21~30, 31~40, and 41~50).

Click Apply to save the settings.

Click Cancel to discard the changes.

802.1X

802.1X Authentication protocol. This protocol is not available with the first released firmware. Please check TRENDware web site (www.trendware.com) for updated firmware that supports 802.1X protocol.

18

Image 19
Contents TEW-310APB TEW-310APBX 2.4 GHz Wireless Access Point + BridgeUsers Guide 5.Using the Configuration Utility CONTENTS1.Package Contents 3.Wireless Basicsinside the box Replacing the antenna with high gain antenna2 Locate antenna connectors 1 Locate the two antennasIf any of the above items are missing, please contact your reseller 1. Package ContentsContents System RequirementsConnections 2. IntroductionFeatures and Benefits LED Indicators 3. Wireless Basics Installation Considerations TRENDware Wireless Family of LAN products includeStandards - Based Technology objects that the wireless signal must pass thru may limit range. Typical ranges vary depending on the types of materials and any background RF radio frequency noise in your home or business. The key to maximizing range is to follow these basic guidelines please remember that the IP Address for each computer must be in 4. Getting StartedIP ADDRESS Setting Up an Infrastructure Network Factory Default Setting for the TEW-310APB 5. Using the Configuration MenuConfiguration Menu Status Screen with Menu Bar AP name SSID Channel WEP Key Mode Basic SettingsAutomatically . Or you can IP SettingsSubnet Mask , and Gateway by AP Mode Advanced SettingsAuthentication Type 802.1X SecurityTools Note Please do not interrupt the firmware upgrade processBased on Windows XP Operating System 6. TroubleshootingGateway Address ∙ Select the Hardware Tab ∙ Click Device Manager ∙ Click Properties∙ Select Properties to check that the drivers are installed properly AdaptersCardbus Adapter ∙ Right-click on 22M Wireless4. Resetting the TEW-310APB to Factory Default Settings Microsoft Windows XP Go to Start Control Panel Network Connections Using the Network Setup Wizard in Windows XPSelect Set up a home or small office network 7. Networking BasicsClick Next Please follow all the instructions in this windowWorkgroup name Enter a Computer description and a Computer nameClick Next Note Each computer should have a unique Computer name Please wait while the wizard applies the changes When the changes are complete, click NextFormat the disk if you wish, and click Next Insert a disk into the Floppy Disk Drive, in this case drive APlease wait while the wizard copies the files Page In Windows XP Naming your ComputerChecking the IP Address in Windows XP/2000 Go to Start All Programs Accessories Command PromptAddress Type Command and click OKControl Panel Assigning a Static IP AddressNetwork Connections ∙ Right-click on Local Area Connections ∙ Click Properties∙ Highlight Internet Protocol TCP/IP You have completed the assignment of a Static IP Address ∙ Input your DNS server address only if you plan to use the Internet∙ Select Obtain an IP address Connecting to a Wireless Network in Windows XPNetwork Connection Internet Protocol TCP/IP click Properties∙ IP address ∙ Subnet mask Connecting to a Wireless Network in WindowsProperties select Internet Protocol TCP/IP click Properties Connecting to a Wireless Network with a Wireless Router or an Access Point using a DHCP server in Windows ∙ Select Detect connection to network media Connecting to a Wireless Network in Windows Me and∙ Go to Start Settings Control Panel Double-click select Internet Protocol TCP/IP click Properties∙ Select Specify an IP address Checking the Wireless Connection by PingingFor Windows XP and Shared Documents folder and Sharing files and folders in the Help and For Windows Me andFile and Printer Sharing Ports 8. Technical SpecificationsDiagnostic LED StandardsHumidity DimensionsWeight TemperatureE-mail support@trendware.com 9. Contacting Technical SupportTRENDware Technical Support over the Telephone Tel +1-310-891-1100 TRENDware Technical Support E-mailAddress