Technical Specifications
For use with Transition Networks Model
Standards: | IEEE 802.3™ 2000, IEEE 802.3x™ |
Data Rate: | 10 Mb/s, 100 Mb/s (copper), 100 Mb/s (fiber) |
Dimensions: | Models 130- & |
| (W x H x D) 4.125" x 6" x 5" (104.77 x 152.4 x 127 mm) |
Dimensions: | Model |
| (W x H x D) 3.375" x 6" x 5" (85.73x 152.4 x 127 mm) |
Weight: | 3.2 lb. (1.5 kg) approximately |
Input Voltage: | |
| |
Power: | 15 W (maximum) |
| Aux input standby power, 200 mW typically |
Fuse: | 2.5 A/250 VDC |
Alarm Relay: | |
| 0.5 A @ 125 VAC / 2.0 A @ 30 VDC (maximum) |
| switching capacity: 60 W (maximum) |
Packet Size: | Memory: 64K Bytes |
| Unicast MAC addresses: 1000 |
| Maximum packet size: 1536 Bytes |
MTBF*: | 51,115 |
| 153,038 Bellcore Hours |
Environment | |
Operating Temp: | |
Storage Temp: | |
Humidity: | 5 to 95%, |
Altitude: | 3000 m (10,000 ft.) |
Warranty: | Lifetime |
The industrial switch is designed for installation in restricted access locations. Installing the industrial switch into other equipment or facility control rooms must comply with the
IMPORTANT: Copper based media ports: e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3, Video Coax, etc. are intended for connecting to
*MTBF is estimated using the predictability method. This method is based on MIL- 217F at 25°C ambient temperature, typical enclosure heat rise of 10°C, and nominal operating conditions and parameters. Installation and configuration specific MTBF estimates are available upon request. Contact Technical Support.
Technical Specification -- continued
220–240VAC, 50/60Hz installation
CAUTION: If the main power source is
EMC Type Tests (all test were performed using unshielded cables)
Standard | Description | Compliance Level | Remarks |
|
|
|
|
EN55022/FCC Part15 | ITE Emissions | Class A | Conducted and radiated |
|
|
|
|
| ITE Emissions |
|
|
|
|
|
|
| Level 2 | ESD contact discharge | |
|
|
|
|
| Level 4 | Radiated fields | |
|
|
|
|
| Level 3 | Fast transients - power port | |
|
|
| 2 meter cable AC |
|
|
| 1 meter cable DC |
|
|
|
|
|
| Level 2 | Fast transient – Ethernet port |
|
|
| 3 meter cable length |
|
|
|
|
| Level 3 CM | Surge – power port | |
|
| Level 2 DM | 2 meter cable AC |
|
| Level 1 DC | 1 meter cable DC |
|
|
|
|
|
| Level 2 | Surge – relay port |
|
|
| 1 meter cable length |
|
|
|
|
|
| Level 2 | Surge – Ethernet port |
|
|
| 3 meter cable length |
|
|
|
|
| Conducted – power port | ||
|
| EN55024 Level 2 | 2 meter cable AC, |
|
|
| 1 meter cable DC |
|
|
|
|
|
| Conducted – relay port | |
|
| EN55024 Level 2 | 1 meter cable length |
|
|
|
|
|
| Conducted – PE Studs | |
|
| EN55024 Level 2 | 2 meter cable length |
|
|
|
|
|
| Conducted – Ethernet port | |
|
| EN55024 Level 2 | 10 meter cable length |
|
|
|
|
| Level 1 | Power freq. mag. field | |
|
|
|
|
| N/A | VoltageDIPs and variations | |
|
|
|
|
IEEE1613, Power Substation Testing |
|
| |
|
|
|
|
IEEE1613, Clause 6.2 |
| Not rated | Dielectric power freq. |
|
|
|
|
IEEE1613, Clause 6.3 |
| Compliant | Impulse voltage all ports |
|
|
|
|
IEEE1613, Clause 7.3.1 |
| Class 2 transverse and | Surge oscillatory waveform |
|
| common Mode | |
|
|
|
|
|
| Class 2 transverse and | Surge oscillatory waveform |
|
| common Mode | |
|
|
|
|
|
| Class 2 common mode | Surge oscillatory waveform |
|
|
| |
|
|
|
|
|
| Class 2 common mode | Surge oscillatory waveform |
|
|
| |
|
|
|
|
|
| Class 1 common mode | Surge oscillatory waveform |
|
|
| – Ethernet 100 Mbps |
|
|
|
|
22 | techsupport@transition.com | 23 |