Transition Networks SUBTF10XX-1XX-MX specifications Troubleshooting, VAC, 50/60Hz

SIBTF10xx-1xx-Mx

Technical Specification -- continued

EMC Type Tests -- Continued

Standard	Description	Compliance Level	Remarks
IEEE1613, Power Substation Testing -- Continued
IEEE1613, Clause 7.3.2		Class 2 transverse mode	Surge fast transient
		Class 1 common mode	waveform – power AC
		Class 2 transverse mode	Surge fast transient
		Class 1 common mode	waveform – power DC
		Class 1 common mode	Surge fast transient
			waveform – relay port
		Class 1 common mode	Surge fast transient
			waveform – Ethernet 10
			Mbps
		Class 1 common mode	Surge fast transient
			waveform – Ethernet 100
			Mbps
IEEE1613, Clause 8		Class 2	Radio frequency
			susceptibility
IEEE1613, Clause 9		Class 1	ESD contact discharge 8kV

Troubleshooting

If the industrial switch fails, isolate and correct the failure by determining the answers to the following questions and then taking the indicated action:

1.	Is the “PRI” (primary power) LED illuminated?
	NO	Ensure the power source is the proper voltage (48–170 VDC or 90–125
	•
		VAC, 50/60Hz).
	•	Ensure that the positive, negative, and ground wires from the power
		source are properly connected to the primary inputs.
	•	Contact Technical Support:	US/Canada: 1-800-260-1312,
			International: 00-1-952-941-7600.
	YES

•Proceed to step 2.

2.(SIBTF10xx10x-MR models only) is the “AUX” (auxiliary power) LED illuminated?

NO

•If the device does not have an auxiliary power source, proceed to step 3.

•Ensure the power source is the proper voltage (48–170 VDC or 90–125 VAC, 50/60Hz).

•Ensure that the positive, negative, and ground wires from the power source are properly connected to the auxiliary inputs.

•Contact Technical Support: US/Canada: 1-800-260-1312, International: 00-1-952-941-7600.

YES

•Proceed to step 3.

Troubleshooting -- continued

3.Is the “FAULT” LED illuminated?

NO

•Proceed to step 4.

YES

•Contact Technical Support: US/Canada: 1-800-260-1312, International:

00-1-952-941-7600.

4.For each port with a cable installed is either the “10MB” or the “100MB” LED illuminated?

YES

•Proceed to step 5.

NO

•For each port with a cable installed and its LED is OFF, check the cable for proper connection.

•For the fiber ports, verify that the TX and RX cables on the SIBTF10xx- 10x are connected to the RX and TX ports, respectively, on the device at the other end of the fiber cables.

•Contact Technical Support: US/Canada: 1-800-260-1312, International:

00-1-952-941-7600

5.For each RJ-45 port with a cable installed (ports 1, 2, 3, and 4), check to see if the 10MB or 100MB LED is illuminated.

•10MB is ON = The industrial switch has selected 10Mb/s operation.

•100MB is ON = The industrial switch has selected 100Mb/s operation.

•If the speed is not correct, disconnect and reconnect the cable to restart the initialization process.

•Proceed to step 6.

6.For each fiber port with a cable installed, is the “FD” (full-duplex)LED illuminated?

NO

•The industrial switch has selected half-duplex mode.

•If the mode is not correct, disconnect and reconnect cable to restart the initialization process.

•Check the cable for proper connection.

•Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

•The industrial switch has selected full-duplex mode.

•If the mode is not correct, disconnect and reconnect cable to restart the initialization process.

•Check the cable for proper connection.

•Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

24 24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600 techsupport@transition.com -- Click the “Transition Now” link for a live Web chat. 25