Fujitsu E8020D manual Exit Menu Leaving the Setup Utility, Exit Saving, Changes, Power Off

Page 28

L i f e B o o k E S e r i e s B I O S

EXIT MENU – LEAVING THE SETUP UTILITY

The Exit Menu is used to leave the setup utility. Follow the instructions for Navigating Through the Setup Utility to make any changes. (See Navigating through the Setup Utility on page 2 for more information.)

The following table shows the names of the menu fields for the Exit menu, the default settings and a description of the field's function and any special information needed to help understand the field's use.

PhoenixBIOS Setup Utility

Main Advanced Security Power Savings Boot Exit

Exit Saving Changes

Exit Discarding Changes

Load Setup Defaults

Discard Changes

Save Changes

Save Changes and Power Off

Item Specific Help

Exit System Setup and save your changes to CMOS.

F1 Help

Select Item

-/SpaceChange Values

ESC Exit

Select Menu

Enter

Select Sub-Menu

 

 

Figure 20.

Exit Menu

Table 20: Fields, Options and Defaults for the Exit Menu

F9 Setup Defaults

F10 Save and Exit

Menu Field

Description

 

 

 

 

Exit Saving

Exit Saving Changes and Exit will store all the entries on every menu of the setup utility to the BIOS memory, then exit

Changes

the utility. A confirmation message Save Configuration changes and exit now? [Yes][No] is displayed.

 

 

Exit Discarding

Selecting Exit Discarding Changes and Exit will exit the setup utility with out writing to the BIOS memory. When the

Changes

BIOS recognizes this selection it will load the operating system and begin operation.

 

 

Load Setup

Selecting Load Setup Defaults will load the factory preset default values for all menu fields, then display the message

Defaults

Load default configuration now? [Yes] [No]. When confirmed the setup utility will return to the Exit

 

Menu. To return to another menu follow the directions in the Navigating Through the Setup Utility Section.

 

 

Discard

Selecting Discard Changes will load the previous values in BIOS memory for all menu fields. The message Load pre-

Changes

vious now? [Yes] [No] will be displayed. When confirmed the setup utility will return to the Exit menu. To return

 

to another menu, follow the directions in the Navigating Through the Setup Utility Section.

 

 

Save Changes

Selecting Save Changes will cause the new settings in all menus to be written to the BIOS memory. The message Save

 

configuration changes now? [Yes] [No] will be displayed. When confirmed, the setup utility will return to

 

the Exit menu. To return to another menu, follow the directions in the Navigating Through the Setup Utility section.

 

 

Save Changes

Selecting Save Changes and Power Off will cause the new settings in all menus to be written to the BIOS memory. The

and Power Off

message Save configuration changes and power off now? [Yes] [No] will be displayed. When con-

 

firmed, the system will shut down. If No is selected, the system will return to the Exit menu. To return to another menu,

 

follow the directions in the Navigating Through the Setup Utility section.

 

 

28

Image 28
Contents Fujitsu LifeBook Series Entering the Bios Setup Utility Bios Setup UtilityNavigating through the Setup Utility I n M e n u Main Menu Setting Standard System Parameters Fields, Options and Defaults for the Main MenuPort 0 submenu Number Serial ATA Port Selects Serial ATA ProductMaster submenu Number of the hard Following Setup items do not appear Serial ATA Port 0 Submenu of the Main MenuAuto Logical Block Addressing LBAPrimary Master Submenu of the Main Menu Is selectedTransfer Mode Standard Exiting from Main MenuAdvanced Menu Setting Device Feature Controls Fields, Options and Defaults for the Advanced MenuMain Advanced Security Boot Info Exit Ing of video signals to different displaysCPU Features USB FeaturesTion SubClass supportEnabled Serial/Parallel Port Configuration SubmenuSerial Port Disabled Enabled To set the mode for the infrared portIs Enabled 278 27F Is Enabled 3BC 3BF InterruptKeyboard/Mouse Features Submenu of the Advanced Menu Video Features Submenu of the Advanced Menu Video Features SubmenuDisabled Enabled Internal Device Configurations Submenu of the Advanced MenuConfiguration Enabled CPU Features Submenu of the Advanced Menu SpeedStepR Disabled EnabledUSB Features Submenu of the Advanced Menu When Enabled is selected, Legacy USB Emulation is enabledKey are enabled. Note that enabling this feature may cause USB devices are available without a USB-aware OSMiscellaneous Configurations Submenu of the Advanced Menu DisabledEvent Logging Submenu of the Advanced Menu Event Logging SubmenuSecurity Menu Setting the Security Features Boot Info ExitFields, Options and Defaults for the Security Menu Exiting from the Security MenuHard Disk Security Submenu of the Security Menu Owner Information Submenu of the Security Menu Owner Information SubmenuSecurity Chip Disabled Security Chip Setting Submenu of the Security MenuReboot Boot Menu Selecting the Operating System Source Fields, Options and Defaults for the Boot MenuQuickBoot Disabled Enabled Enabled Fewer tests mean faster startup Boot-time DisabledBoot Device Priority Submenu of the Boot Menu Exiting from Boot MenuInfo Menu Displays Basic System Information Fields, Options and Defaults for the Info MenuCPU Speed 00 GHz Memory Slot None Exit Menu Leaving the Setup Utility Fields, Options and Defaults for the Exit MenuPower Off Exit Saving