Fujitsu 500 user manual Insert the expansion card into the slot, Install the mounting bracket

Page 54

5Insert the expansion card into the slot.

Insert the expansion card into the slot, and secure it with the screw removed in step 4.

6Install the mounting bracket.

Install the reinforcement bracket to the three stoppers on the PC unit.

Stopper

7 Reinstall the upper cover.

Point

•For removal, use the installation procedure in the reverse order.

8Plug the PC.

9Turn on the PC.

• Windows Me/98/95/2000 models

The system configures the device driver and resource to enable the expansion card.

Point

•The device drivers automatically selected by Plug & Play are those included in Windows Me/ 98/95/2000. The device drivers for some expansion cards or peripheral devices may not be included in these operating systems. If so, use a CD-ROM containing the device driver sup- plied with the expansion card and install it by following the messages.

•Before using the installed expansion card, use Device Manager to check whether the device driver is installed. If not, delete the device driver and then reboot Windows Me/98/95/2000.

•Windows NT models

Configure the device driver for the expansion card.

Refer to the manual for the expansion card. Once the device driver is configured, the expansion card is enabled.

43

Image 54

Contents Deskpower 5000 Series User’s Manual Important Safety Instructions Iii Safety product applications Before Starting Your PCFor Safe Operations Conventions used in this manual PointDiskcopy a a Command entry from keyboardCD-ROM drive¥setup.exe Sample screens IllustrationsDeskpower Rear surface of the equipmentManual configuration IntroductionContent IntroductionChapter Hardware Specifications Chapter Part Names and Functions Front of the PC unitHard disk access lamp Power lampPower switch Floppy disk drive access lampRear of the PC unit CRT connector Keyboard connector Connect the keyboard Serial connectorParallel connector DVI connectorPower supply unit Inch front access bay Inside the PC unitInternal hard disk drive Primary IDE connector IDE1 Internal batteryDimm slots Keyboard Windows key Caps Lock/Alphanumeric keyCtrl control key Alt keyMouse Using the mouseUsing the mouse buttons Moving the mouseDouble-clicking PointingDragging Vertical placement InstallationInstallation area Using two feetUsing one foot Mount the feet on the PC unitMount the disassembled foot on the PC unit Horizontal placement Disassemble the feetPlace the PC unit on the disassembled feet Example of installation Vertical placementHorizontal placement Connection Connect the power cable to the outlet Connect the power cable to the displayConnect the mouse Connect the LAN cable Connect the keyboardConnect the display cable to the PC unit Connect the LAN cable to the networkConnecting the power cable Page Turning On the Power Turning on the power Press the power switch on the displayPress the power switch on the PC Turning Off the Power Supply Turning off the powerWindows Me Windows 98/95 WindowsWindows NT Restarting Restarting the PCPoint CD-ROM Removing the CD Inserting or removing a CDInserting a CD Press the Eject buttonFloppy Disk Inserting or removing a floppy disk PointInserting a floppy disk Confirm that the Floppy disk access lamp is off Removing the floppy diskHardware Before Installing a Peripheral Device Page Removing the Cover Removing the upper coverRemove the upper cover Removing the reinforcement bracket Installing Memory Modules Memory module installation procedure Location of memory modulesApplicable memory modules Installing Memory Modules Memory module combinationsInsert a memory module into the slot Installing an Expansion Card Location of expansion cards Applicable expansion cardsInstalling an Expansion Card Remove the slot coverPlug the PC Turn on the PC Windows Me/98/95/2000 models Install the mounting bracketInsert the expansion card into the slot Windows NT modelsInstalling an Internal Option Location of internal optionsPage Installing an Internal Hard Disk Drive Installing a device in the 3.5-inch front access bayInstalling Other Internal Options Make a setting on the option to be installedInstall the internal option on the PC unit Connect the flat cable Master SlaveConnect the power cable Troubleshooting Problems Mouse cursor does not move Characters entered using the keyboard are not displayedData cannot be read from the CD-ROM drive Windows Me/98/95Technical Information Maintenance of the keyboard Maintenance of the HardwareMaintenance of the PC unit Cleaning CDsMaintenance of the mouse Cleaning the floppy disk driveAdditional Cautions Preventing Television or Radio InterferenceUSB Windows Me/98/95/2000 models Wakeup On LAN USB keyboard Windows 98 modelsAddition of a LAN card Digital display outputVideo memory capacity display Power-saving function of displayConnecting the display Replacing the displayMouse with a scrolling function scrolling wheel Power-saving functionInternational EnergyStar Program Intel processor serial numberHardware Specifications PC unit specificationsProduct name LAN adapter specifications CSMA/CDSound specifications Graphical specificationsConnector specifications TXC+ LAN connector 100BASE-TX/10BASE-T Mouse connector Keyboard connector Index CD-ROM driveMouse Clicking