Fujitsu 500 user manual Installing an Internal Hard Disk Drive

Page 57

Installing an Internal Hard Disk Drive

This section explains how to install a second internal hard disk drive to your PC.

Cautions

To prevent faults, note the following.

Data is read from the hard disk drive or written to it while the internal disk that stores data is rotating at high speeds. Since it is a very delicate device, do not carry the PC with the power on or do not apply shock or vibration to the PC.

Do not use or store the hard disk drive in an area where temperature changes sharply in an extremely wide range.

Do not place the hard disk drive in an area exposed to direct sunlight or near a heater.

Do not use or store the hard disk drive in an area subjected to shock or vibration.

Do not use or store the hard disk drive in a humid or dusty area.

Do not use or store the hard disk drive near a magnet or device that generates a strong magnetic field.

Do not disassemble or break down the hard disk drive.

Keep the hard disk drive free from condensation or moisture.

￿Point

Improper handling may damage the data stored on the disk. Always make backup copies of important data.

Even hard disks of the same type have different capacities. It is recommended to back up data not in units of hard disks but in units of files or sectors.

Installing a device in the 3.5-inch front access bay

In installing the hard disk drive in the front access bay, see “Installing Other Internal Options”.

46

Image 57
Contents Deskpower 5000 Series User’s Manual Important Safety Instructions Iii Safety product applications Before Starting Your PCFor Safe Operations Point Conventions used in this manualCD-ROM drive¥setup.exe Sample screens Command entry from keyboardDiskcopy a a IllustrationsRear surface of the equipment DeskpowerIntroduction Manual configurationIntroduction ContentChapter Hardware Specifications Chapter Front of the PC unit Part Names and FunctionsPower switch Power lampHard disk access lamp Floppy disk drive access lampRear of the PC unit Parallel connector Keyboard connector Connect the keyboard Serial connectorCRT connector DVI connectorPower supply unit Inch front access bay Inside the PC unitInternal hard disk drive Primary IDE connector IDE1 Internal batteryDimm slots Keyboard Ctrl control key Caps Lock/Alphanumeric keyWindows key Alt keyUsing the mouse buttons Using the mouseMouse Moving the mouseDouble-clicking PointingDragging Installation area InstallationVertical placement Using two feetUsing one foot Mount the feet on the PC unitMount the disassembled foot on the PC unit Horizontal placement Disassemble the feetPlace the PC unit on the disassembled feet Example of installation Vertical placementHorizontal placement Connection Connect the power cable to the outlet Connect the power cable to the displayConnect the mouse Connect the display cable to the PC unit Connect the keyboardConnect the LAN cable Connect the LAN cable to the networkConnecting the power cable Page Turning On the Power Turning on the power Press the power switch on the displayPress the power switch on the PC Turning Off the Power Supply Turning off the powerWindows Me Windows 98/95 WindowsWindows NT Restarting the PC RestartingPoint CD-ROM Inserting a CD Inserting or removing a CDRemoving the CD Press the Eject buttonFloppy Disk Inserting or removing a floppy disk PointInserting a floppy disk Removing the floppy disk Confirm that the Floppy disk access lamp is offHardware Before Installing a Peripheral Device Page Removing the Cover Removing the upper coverRemove the upper cover Removing the reinforcement bracket Installing Memory Modules Memory module installation procedure Location of memory modulesApplicable memory modules Memory module combinations Installing Memory ModulesInsert a memory module into the slot Installing an Expansion Card Applicable expansion cards Location of expansion cardsRemove the slot cover Installing an Expansion CardInsert the expansion card into the slot Install the mounting bracketPlug the PC Turn on the PC Windows Me/98/95/2000 models Windows NT modelsLocation of internal options Installing an Internal OptionPage Installing a device in the 3.5-inch front access bay Installing an Internal Hard Disk DriveMake a setting on the option to be installed Installing Other Internal OptionsInstall the internal option on the PC unit Master Slave Connect the flat cableConnect the power cable Troubleshooting Problems Data cannot be read from the CD-ROM drive Characters entered using the keyboard are not displayedMouse cursor does not move Windows Me/98/95Technical Information Maintenance of the PC unit Maintenance of the HardwareMaintenance of the keyboard Cleaning CDsCleaning the floppy disk drive Maintenance of the mouseAdditional Cautions Preventing Television or Radio InterferenceUSB Windows Me/98/95/2000 models Addition of a LAN card USB keyboard Windows 98 modelsWakeup On LAN Digital display outputConnecting the display Power-saving function of displayVideo memory capacity display Replacing the displayInternational EnergyStar Program Power-saving functionMouse with a scrolling function scrolling wheel Intel processor serial numberHardware Specifications PC unit specificationsProduct name CSMA/CD LAN adapter specificationsSound specifications Graphical specificationsConnector specifications TXC+ LAN connector 100BASE-TX/10BASE-T Mouse connector Keyboard connector CD-ROM drive IndexMouse Clicking