Fujitsu 500 user manual

Page 56

Cautions

On Windows 98 systems, if you want to disconnect the device from the master connector of the secondary IDE and connect it to the slave connector, you must change the system settings beforehand.

If you want to install an internal option to your PC, set up Windows, turn off the PC, and then install the option.

An internal hard disk drive that supports DMA (Multiword DMA1/2, Ultra DMA/33, or Ultra DMA/66) can be used with the DMA setting.

When installing a hard disk drive or magneto-optical disk drive that does not support DMA, be sure to set DMA to OFF. If it is used with DMA set to ON, the drive may not work properly and may destroy data.

Refer to the manual for the hard disk drive or magneto-optical disk drive to check whether it supports DMA.

The secondary IDE does not support Ultra DMA/66 and Ultra DMA/100. Use the secondary IDE in the Ultra DMA/33, Multiword DMA1/2, or PIO mode.

This PC does not support additional floppy disk drive.

CAUTION

• Before installing or removing an internal option, turn off the PC and all devices connected to it, and unplug them. Otherwise, an electric shock may occur.

• Use Fujitsu-supplied internal options.

Otherwise, an electric shock, a fire or fault may occur.

WARNING

• When installing or removing an internal option, do not remove screws other than those specified.

Otherwise, personal injury or faults may occur.

• When accessing the PC board, touch the specified areas only. Otherwise, you may be injured or a fault may occur.

45

Image 56
Contents Deskpower 5000 Series User’s Manual Important Safety Instructions Iii For Safe Operations Safety product applicationsBefore Starting Your PC Conventions used in this manual PointCommand entry from keyboard CD-ROM drive¥setup.exe Sample screensDiskcopy a a IllustrationsDeskpower Rear surface of the equipmentManual configuration IntroductionContent IntroductionChapter Hardware Specifications Chapter Part Names and Functions Front of the PC unitPower lamp Power switchHard disk access lamp Floppy disk drive access lampRear of the PC unit Keyboard connector Connect the keyboard Serial connector Parallel connectorCRT connector DVI connectorInternal hard disk drive Power supply unit Inch front access bayInside the PC unit Dimm slots Primary IDE connector IDE1Internal battery Keyboard Caps Lock/Alphanumeric key Ctrl control keyWindows key Alt keyUsing the mouse Using the mouse buttonsMouse Moving the mouseDragging Double-clickingPointing Installation Installation areaVertical placement Using two feetMount the disassembled foot on the PC unit Using one footMount the feet on the PC unit Place the PC unit on the disassembled feet Horizontal placementDisassemble the feet Horizontal placement Example of installationVertical placement Connection Connect the mouse Connect the power cable to the outletConnect the power cable to the display Connect the keyboard Connect the display cable to the PC unitConnect the LAN cable Connect the LAN cable to the networkConnecting the power cable Page Turning On the Power Press the power switch on the PC Turning on the powerPress the power switch on the display Windows Me Turning Off the Power SupplyTurning off the power Windows NT Windows 98/95Windows Restarting Restarting the PCPoint CD-ROM Inserting or removing a CD Inserting a CDRemoving the CD Press the Eject buttonInserting a floppy disk Floppy DiskInserting or removing a floppy disk Point Confirm that the Floppy disk access lamp is off Removing the floppy diskHardware Before Installing a Peripheral Device Page Remove the upper cover Removing the CoverRemoving the upper cover Removing the reinforcement bracket Installing Memory Modules Applicable memory modules Memory module installation procedureLocation of memory modules Installing Memory Modules Memory module combinationsInsert a memory module into the slot Installing an Expansion Card Location of expansion cards Applicable expansion cardsInstalling an Expansion Card Remove the slot coverInstall the mounting bracket Insert the expansion card into the slotPlug the PC Turn on the PC Windows Me/98/95/2000 models Windows NT modelsInstalling an Internal Option Location of internal optionsPage Installing an Internal Hard Disk Drive Installing a device in the 3.5-inch front access bayInstalling Other Internal Options Make a setting on the option to be installedInstall the internal option on the PC unit Connect the flat cable Master SlaveConnect the power cable Troubleshooting Problems Characters entered using the keyboard are not displayed Data cannot be read from the CD-ROM driveMouse cursor does not move Windows Me/98/95Technical Information Maintenance of the Hardware Maintenance of the PC unitMaintenance of the keyboard Cleaning CDsMaintenance of the mouse Cleaning the floppy disk driveUSB Windows Me/98/95/2000 models Additional CautionsPreventing Television or Radio Interference USB keyboard Windows 98 models Addition of a LAN cardWakeup On LAN Digital display outputPower-saving function of display Connecting the displayVideo memory capacity display Replacing the displayPower-saving function International EnergyStar ProgramMouse with a scrolling function scrolling wheel Intel processor serial numberProduct name Hardware SpecificationsPC unit specifications LAN adapter specifications CSMA/CDConnector specifications Sound specificationsGraphical specifications TXC+ LAN connector 100BASE-TX/10BASE-T Mouse connector Keyboard connector Index CD-ROM driveMouse Clicking