IBM 32x, W2H, 31x manual Industry Canada class a emission compliance statement, Germany

Page 50

11-9-2005

Electronic emission notices

Federal communications commission (FCC) statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada class A emission compliance statement

This Class A digital apparatus complies with Canadian ICES-003.

Avis de conformité aux normes d’Industrie Canada

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du

Canada.

European Community (CE) mark of conformity statement

This product is in conformity with the protection requirements of EC Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards.

This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22 / European Standard EN 55022. The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment.

Warning: This is a Class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.

Germany

Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von Geräten (EMVG) vom 30. August 1995 (bzw. der EMC EG Richlinie 89/336).

B-2SurePOS Installation and Service

Image 50
Contents SurePOS Page SurePOS Second Edition March Contents Iv SurePOS Installation and Service Figures Vi SurePOS Installation and Service Who should read this manual Driver and Service Diskette InformationAbout this guide Related publicationsEnd of life disposal AccessibilityUninterruptible power supply option About this guide Tell us what you think Summary of changes Xii SurePOS Installation and Service Introduction Physical dimensions Product introductionFront view and LEDs Environmental considerationsRear connectors Rear connectors 4810 31x modelsPower Rear connectors 32x models 4shows the connections available on the 4810/4910 modelsPower. The voltage switch allows you to select 8SurePOS Installation and Service Disassembling the 4810/4910 SurePOS View of componentsBracket assembly and hard drive On page 1-4to locate the voltage selection switch 4SurePOS Installation and Service Problem determination Preliminary checklistProblem determination Parts catalog Assembly 1 Field-replaceable units Assembly 4SurePOS Installation and Service Emulation mode select 00 Null Appendix A. Input/output device commandsCharacter display VFD commands Character set select 02 STXLogic Controls Emulation Mode User character definition 03 EXTIBM Mode Bit Byte #Brightness control 04 EOT Alphanumeric message scroll 05 ENGBackspace 08 BS Normal Display Control Mode DC1Vertical Scroll Display Control Mode DC2 Horizontal tab 09 HTTest 0F SI Normal-display control mode 11 DC1Carriage return 0D CR Display position 10 DLECursor on 13 DC3 Vertical-scroll display control mode 12 DC2Reset 1F US Cursor off 14 DC4Null VFD Commands Line feed APA commandsBackspace without deleting Clear display Carriage returnTest Display positionDimming Cursor modeScreen mode Display mode set Horizontal scrollJapanese User-definable font setFont size At the all language X20--XFF English Horizontal scroll on all lines Graphic display modeDouble-size letter in horizontal Format of the Horizontal Scroll Start command is as follows Null Commands Font selectionAppendix B. Notices European Community CE mark of conformity statement Industry Canada class a emission compliance statementAvis de conformité aux normes d’Industrie Canada GermanyAppendix B. Notices B-3 Korean Communications Statement ESD Damage Prevention Handling Removed CardsTrademarks Appendix C. Safety information GevaarPerigo FareVorsicht VigyázatPericolo PeligroVarning-livsfara IBM GA27-4004 IBM GA27-4004 8SurePOS Installation and Service Index Numerics APA A-9Power Cooling Light off Power supply Readers’ Comments We’d Like to Hear from You How satisfied are you that the information in this book isBusiness Reply Mail Page Part Number 03R5994