Cisco Systems ME 2400 manual LEDs, SFP Module Patch Cable, System LED

Page 23

Chapter 1 Product Overview

Front Panel Description

SFP Module Patch Cable

The Cisco ME switch supports the SFP module patch cable, a 1/2 meter, copper, passive cable with SFP module connectors at each end (see Figure 1-3). The patch cable can connect two Cisco ME switches in a cascaded configuration.

Figure 1-3 SFP Module Patch Cable

126809

See “Inserting and Removing the SFP Module Patch Cable” section on page 2-21for more information about using the SFP module patch cable.

LEDs

You can use the switch System and port LEDs to monitor switch activity and performance.

System LED

Figure 1-4shows the switch System LED.

Figure 1-4 Cisco ME Switch System LED

1

SYSTEM

	RATING
	100-
1A	240V		~
1A	-0.5A,		~
	-0.5A,	50-60		HZ
		50-60

1System LED

CONSOLE

132661

Cisco ME 2400 Ethernet Access Switch Hardware Installation Guide

	OL-7678-01	1-5

Image 23

Contents Corporate Headquarters Cisco Systems, Inc. All rights reserved N T E N T S Preparing for Installation Crossover Cable and Adapter Pinouts B-5 OL-7678-01 Organization AudiencePurpose Bewaar Deze Instructies ConventionsSäilytä Nämä Ohjeet Guarde Estas Instruções GEM Disse Anvisninger Xii Xiii Related PublicationsProduct Documentation DVD Obtaining DocumentationCisco.com Ordering Documentation Documentation FeedbackCisco Product Security Overview Cisco Technical Support & Documentation Website Reporting Security Problems in Cisco ProductsObtaining Technical Assistance Definitions of Service Request Severity Submitting a Service RequestObtaining Additional Publications and Information Features Setting up the SwitchFront Panel Description 10/100 Ports Front Panel DescriptionsSFP Modules SFP Module SlotsSystem LED LEDsSFP Module Patch Cable Port LEDs Rear Panel DescriptionManagement Options Power ConnectorsCisco ME AC Switch Power Supply Cisco ME DC Switch Power SupplyNetwork Configurations Preparing for Installation Switch InstallationStatement 122F 50C Statement Micron MHz/km Cable Distance Installation GuidelinesGLC-SX-MM Verifying Package Contents Rack-Mounting Verifying Switch OperationInstalling the Switch Powering Off the SwitchRemoving Screws from the Cisco ME Switch Removing Screws from the SwitchRack-Mounting Brackets Attaching Brackets to the SwitchAttaching Brackets to 19-Inch Racks Attaching Brackets for 23-Inch Racks Attaching Brackets to 24-Inch Racks 132665 Attaching Brackets for Etsi Racks 15 Mounting the Cisco ME Switch in a Rack Mounting the Switch in a RackAttaching the Cable Guide Attaching the Brackets to the Switch for Wall-MountingWall-Mounting 18 Mounting the Switch on a Wall Mounting the Switch on a WallTable- or Shelf- Mounting Installing and Removing SFP ModulesInstalling SFP Modules into SFP Module Slots 19 SFP Module with a Bale-Clasp Latch Removing SFP Modules from SFP Module Slots Inserting and Removing the SFP Module Patch Cable 24 Connecting to an Ethernet Port Connecting to the 10/100 PortsConnecting to Fiber-Optic SFP Modules Connecting to SFP Modules26 Connecting to a 1000BASE-T SFP Module Connecting to 1000BASE-T SFP ModulesWhere to Go Next OL-7678-01 Understanding Post Results Diagnosing ProblemsSymptom Possible Cause Resolution Errdisable recovery cause SFP module might be installed Verify that the SFP module is Technical Specifications OL-7678-01 Connector Specifications Connector and Cable SpecificationsSFP Module Ports Figure B-2 Fiber-Optic SFP Module LC ConnectorTwo Twisted-Pair Cable Pinouts Cable and Adapter SpecificationsTP3 Four Twisted-Pair Cable Pinouts for 1000BASE-T PortsAdapter Pinouts Crossover Cable and Adapter PinoutsIdentifying a Crossover Cable Switch Console RJ-45-to-DB-25 Port DTE Connecting to DC Power Preparing the Ground Wire Grounding the SwitchTorque to 15 lbf-in Connecting the Grounding Wire to Earth Ground Wiring the DC-Input Power Source Console Figure C-9 Inserting Wires in the Terminal Block Plug Figure C-10 Torquing the Terminal-Block Captive Screws Figure C-12 Inserting the Terminal Block in the Block Header OL-7678-01 Accessing the CLI Through the Console Port Configuring the Switch with the CLI-Based Setup ProgramTaking Out What You Need Cisco ME DC switch DC power cordConnecting to the Console Port Starting the Terminal-Emulation Software Figure D-3 Connecting the Switch to a PCIP Settings Connecting to a Power SourceEntering the Initial Configuration Information Completing the Setup Program These choices appear OL-7678-01 Numerics IN-2 IN-3 IN-4 IN-5 IN-6