Cisco Systems WSC2960X24TSL, WSC2960X24TDL, WSC2960X48TSL Monitor session sessionnumber source

Page 104

Configuring SPAN and RSPAN

Configuring an FSPAN Session

Command or Action

Step 2 no monitor session {session_number all local remote}

Example:

Switch(config)# no monitor session 2

Step 3 monitor session session_number source

{interface interface-id vlan vlan-id} [,

-] [both rx tx]

Example:

Switch(config)# monitor session 2 source interface gigabitethernet1/0/1

Purpose

Removes any existing SPAN configuration for the session.

•For session_number, the range is 1 to 66.

•all—Removes all SPAN sessions.

•local—Removes all local sessions.

•remote—Removes all remote SPAN sessions.

Specifies the SPAN session and the source port (monitored port).

•For session_number, the range is 1 to 66.

•For interface-id, specify the source port or the source VLAN to monitor.

•For source interface-id, specify the source port to monitor. Only physical interfaces are valid.

•For vlan-id, specify the source VLAN to monitor. The range is 1 to 4094 (excluding the RSPAN VLAN).

Note A single session can include multiple sources (ports or VLANs) defined in a series of commands, but you cannot combine source ports and source VLANs in one session.

•(Optional) [, -] Specifies a series or range of interfaces. Enter a space before and after the comma; enter a space before and after the hyphen.

•(Optional) [both rx tx] Specifies the direction of traffic to monitor. If you do not specify a traffic direction, the SPAN monitors both sent and received traffic.

◦both—Monitors both sent and received traffic. This is the default.

◦rx—Monitors received traffic.

◦tx—Monitors sent traffic.

Note You can use the monitor session session_number source command multiple times to configure multiple source ports.

Step 4 monitor session session_number destination {interface interface-id[, -] [encapsulation replicate]}

Example:

Switch(config)# monitor session 2 destination interface gigabitethernet1/0/2 encapsulation replicate

Specifies the SPAN session and the destination port (monitoring port).

•For session_number, specify the session number entered in Step 3.

•For destination, specify the following parameters:

◦For interface-id, specify the destination port. The destination interface must be a physical port; it cannot be an EtherChannel, and it cannot be a VLAN.

◦(Optional) [, -] Specifies a series or range of interfaces. Enter a space before and after the comma; enter a space before and after the hyphen.

 

Catalyst 2960-X Switch Network Management Configuration Guide, Cisco IOS Release 15.0(2)EX

92

OL-29044-01

Page 103 Page 105
Image 104
Page 103 Page 105
Contents Americas Headquarters First Published July 10Page N T E N T S Configuring the Cisco Discovery Protocol Configuring Simple Network Management Protocol Rspan Vlan Vii Viii Bold font Document ConventionsConvention Description Reader Alert Conventions Obtaining Documentation and Submitting a Service Request Related DocumentationXii Information About Using the Command-Line Interface Command ModesMode Access Method Prompt Exit Method About This Mode ConfigureQuit Ctrl-ZUsing the Help System Command or Action Purpose StepMode HelpCLI Error Messages Understanding Abbreviated CommandsNo and default Forms of Commands How to Use the CLI to Configure Features Configuration LoggingConfiguring the Command History Error Message MeaningCommand or Action Changing the Command History Buffer SizeRecalling Commands Enabling and Disabling Editing Features Disabling the Command History FeaturePrivileged Exec mode Terminal no historyEditing Commands through Keystrokes Editing Command Lines That Wrap Searching and Filtering Output of show and more Commands Access-listShow more command begin include exclude regular-expression Show more command begin include excludeCommand or Action Example OL-29044-01 Finding Feature Information Prerequisites for Configuring the Configuration EngineRestrictions for Configuring the Configuration Engine Information About Configuring the Configuration EngineCisco Configuration Engine Software Related TopicsConfiguration Service Cisco Configuration Engine Architectural OverviewEvent Service Cisco Networking Services IDs and Device HostnamesConfigID NameSpace MapperHostname and DeviceID Hostname, DeviceID, and ConfigIDDeviceID Initial Configuration Cisco IOS CNS AgentsAutomated CNS Configuration Incremental Partial ConfigurationSynchronized Configuration Device Required ConfigurationHow to Configure the Configuration Engine Configure terminalEnabling the CNS Event Agent EndConfigure terminal Enters the global configuration mode Reconnect-time time backupEnabling the Cisco IOS CNS Agent Cns config initial hostname ip-addressCns config partial hostname ip-address Enabling an Initial Configuration for Cisco IOS CNS Agent Command or Action PurposeOn the switch End Returns to privileged Exec modeConfigure terminal Cns template connect name Exit Hostname nameExit Returns to global configuration mode Discover controller controller-typedlciHostname string string udi event image command ExitPort-number event no-persist Source ip-address syntax-checkShow cns event connections Show cns config connectionsRefreshing DeviceIDs No cns event ip-address port-number Enabling a Partial Configuration for Cisco IOS CNS Agent Cns config partial ip-addresshostnameMonitoring CNS Configurations Command PurposeAdditional References Technical Assistance Description LinkRelease Modification Cisco IOS 15.02EXInformation About CDP CDP OverviewHow to Configure CDP Default CDP ConfigurationConfiguring CDP Characteristics FeatureOptional Configures CDP to send Version-2 advertisements Disabling CDP Configure terminal No cdp run EndNo cdp run Disables CDP Enabling CDP Configure terminal Cdp run EndCdp run Enables CDP if it has been disabled No cdp enable End Enters interface configuration modeDisabling CDP on an Interface Specifies the interface on which you are disabling CDPCdp enable End Enabling CDP on an InterfaceCdp enable Enables CDP on a disabled interface Command DescriptionMonitoring and Maintaining CDP Specifies the interface on which you are enabling CDPCommand Show cdp neighbors interface-idShow cdp traffic Related Documents Related Topic Document TitleFeature History and Information for Cisco Discovery Protocol Prerequisites for Snmp Supported Snmp VersionsModel Level Authentication Encryption Result SHA Restrictions for Snmp Information About SnmpSnmp Overview Snmp Manager FunctionsSnmp Community Strings Snmp MIB Variables AccessSnmp Agent Functions Snmp Notifications Snmp ifIndex MIB Object ValuesDefault Snmp Configuration Snmp Configuration GuidelinesFeature Default Setting Interface TypeDisabling the Snmp Agent How to Configure SnmpConfigure terminal No snmp-server End Configuring Community Strings No snmp-server Disables the Snmp agent operationSwitchconfig# access-list 4 deny any Configuring Snmp Groups and Users Snmp-server engineID localSnmp-server user username V1 is the least secure of the possible security modelsIntegers twice the normal width Configuring Snmp Notifications End ExampleNotification Type Keyword Description Snmp-server enable traps port-security Snmp-server enable traps port-security trap-rate ratePort-security RtrV2c access access-list v3 encrypted access Snmp-server user username group-nameremoteRange is 1 to 1000 the default is Setting the Agent Contact and Location Information Snmp-server location text Sets the system location string Limiting Tftp Servers Used Through SnmpSnmp-server contact text Sets the system contact string Monitoring Snmp Status Snmp-server tftp-server-listSnmp Examples Switchconfig# snmp-server enable traps entity Configuring Span and Rspan Prerequisites for Span and RspanRestrictions for Span and Rspan RspanFlow-Based Span Fspan and Flow-Based Rspan Frspan Local Span Information About Span and RspanSpan and Rspan Example of Local Span Configuration on a Single Device Remote SpanExample of Rspan Configuration Span and Rspan Concepts and TerminologySpan Sessions Source Ports Source VLANs Rspan Vlan Span and Rspan Interaction with Other Features Flow-Based Span Span and Rspan and Device StacksSpan Configuration Guidelines Default Span and Rspan ConfigurationConfiguration Guidelines How to Configure Span and Rspan Rspan Configuration GuidelinesFspan and Frspan Configuration Guidelines Creating a Local Span SessionMonitor session sessionnumber source Both rx txEnd No monitor session sessionnumber all Local remoteCommand or Action Purpose Specifying VLANs to FilterConfiguring a Vlan as an Rspan Vlan Monitor session sessionnumber filter vlanRemote-span End Remote-spanCreating an Rspan Source Session Monitor session sessionnumber Destination remote vlan vlan-idSwitchconfig# no monitor session Creating an Rspan Destination Session Remote vlan vlan-id Switchconfig# monitor session 2 source remote vlan Configuring an Fspan Session Configure terminal Enters global configuration modeMonitor session sessionnumber source Configuring an Frspan Session Detailed Steps Show monitor Or Frspan configurationMonitoring Span and Rspan Operations Span and Rspan Configuration Examples Example Configuring Local SpanFeature History and Information for Span and Rspan Examples Creating an Rspan VlanLimit IPv4, IPv6 or IPv4 + IPv6, or D E Span sessions
Related manuals
Manual 18 pages 20.28 Kb

WSC2960X24TSL, C2960XSTACK, WSC2960X24PDL, WSC2960X24TSLL, WSC2960X24PSL specifications

Cisco Systems has long been a leader in networking technology, and its range of switching products exemplifies its commitment to high performance and reliability. Among its popular offerings are the Catalyst 2960-X and 2960-XR series switches, including models like WSC2960X48TSL, WSC2960XR48FPDI, WSC2960XR24TDI, and WSC2960XR48LPDI. These switches are designed to deliver efficient Layer 2 and Layer 3 capabilities, making them ideal for enterprise and small to medium-sized business networks.

The WSC2960X48TSL model boasts 48 Ethernet ports, providing ample connectivity for various devices. It supports Power over Ethernet (PoE), making it suitable for powering IP cameras, wireless access points, and VoIP phones. The switch also features Cisco’s Smart Operations technology, which simplifies network management and enhances user experience through automated features such as Cisco Auto Smartports and Auto QoS.

Turning to the WSC2960XR48FPDI, this version also features 48 ports but with enhanced redundancy and power capabilities, making it suitable for critical applications where uptime is paramount. This switch offers dual power supply options, ensuring that even in the event of a power failure, network operations continue seamlessly. Its Flexible NetFlow feature enables enhanced visibility and monitoring of traffic, allowing businesses to optimize their bandwidth usage and troubleshoot issues more efficiently.

The WSC2960XR24TDI model, with its 24 ports, is perfectly designed for networks with fewer devices yet still demands robust performance. It also includes advanced security features, such as IEEE 802.1X port-based authentication, enhancing the protection of sensitive data and communications within the network.

Lastly, the WSC2960XR48LPDI model is tailored for environments that require high availability and robust performance, featuring 48 ports along with Layer 3 static routing capabilities. With its support for IPv6 and advanced QoS features, this switch is prepared for the future of networking, accommodating the increasing demand for bandwidth and reliable connectivity.

All these switches utilize Cisco IOS software, providing a familiar interface for network administrators. They also incorporate advanced troubleshooting tools, like Cisco Prime, which facilitate effective network management. Collectively, the WSC2960 series switches represent a comprehensive solution for businesses seeking dependable, scalable, and manageable networking options. With their combination of performance, features, and reliability, these Cisco switches are essential for meeting the demands of modern networking.
Top Page Image Contents