Cisco Systems SFS 7000D, SFS 7000P manual IN-9

Page 79

Index

Self-Test, power supply 6-7Self tests 6-1

sensor information, display 5-7Sensors tab 5-6

serial console, attach 3-8shock 2-4

site preparation, checklist 2-6site requirements 2-1specifications

electrical A-2general A-1management A-1

spikes 2-4status

fan 1-3

overall system 1-3power 1-3

show link 1-3stop bits 3-9subnet manager 1-4Summary tab 5-5switch

components 1-2LED 1-3

system information, display 5-6

conditions 2-2extreme 2-2

fluctuations 2-2

transients 2-4

U

undervoltage 2-4

unused module bay 4-2

V

ventilation 2-2,2-5

vibration 2-4

voltage, variations 2-4

W

warning

definition ix

safety 2-1

statement ix, 3-2

statement,translations ix

T

temperature

		Cisco SFS 7000P and SFS 7000D InfiniBand Server Switches Hardware Installation Guide

	OL-10853-01			IN-9
	OL-10853-01			IN-9

Image 79

Contents Text Part Number OL-10853-01 Corporate HeadquartersPage Iii N T E N T SLatency Managing the Switch Chassis and Management Interface A-1 Chapter Title Description PrefaceAudience OrganizationConvention Description ConventionsViii Warnung Wichtige Sicherheitshinweise Bewaar Deze InstructiesAviso Instruções Importantes DE Segurança Avvertenza Importanti Istruzioni Sulla SicurezzaPage Xii GEM Disse AnvisningerXiii Xiv Related DocumentationObtaining Documentation Cisco.comProduct Documentation DVD Ordering Documentation You can access international Cisco websites at this URLDocumentation Feedback Cisco Product Security OverviewProduct Alerts and Field Notices Reporting Security Problems in Cisco ProductsXvi Cisco Technical Support & Documentation Website Obtaining Technical AssistanceXvii Xviii Submitting a Service RequestDefinitions of Service Request Severity Obtaining Additional Publications and InformationXix OL-10853-01 Product Overview Introduction to SwitchesSwitch Components Switch ConnectorsLEDs System FeaturesPower Supply Bay Power Supply ModuleHigh Availability ScalabilityAdministrative Features OL-10853-01 Safety Preparation for InstallationSite Requirements Humidity TemperatureAltitude Corrosion Dust and ParticlesElectromagnetic and Radio Frequency Interference Shock and Vibration Power Source InterruptionsPreventing Electrostatic Discharge Damage Air Flow Power RequirementsTask No Planning Activity Verified By Time Date Site Preparation ChecklistInstalling the Switches Pre-installation Instructions Requirements Rack-Mounting the SwitchesRack-Mounting the Switch Place the switch on a secure, clean surfaceInstalling the Switch with One Person Holding Bracket Inside of Rack Installing the Switch with Two People Obtaining an IP Address Configuring Basic ConnectivityFollowing sections appear in this section Obtaining a Static IP Address for Ethernet Management SFS-7000Dconfig#address-option static Enter the enable commandEnter the configure command to enter the configuration mode SFS-7000Dconfig#interface mgmt-ethernetSFS-7000D#copy running-config startup-config Connecting the 10/100 Ethernet Management PortPowering Up the Chassis Save the configuration to preserve it between rebootsConnecting Network Devices To connect InfiniBand devices, follow these steps Connecting InfiniBand Devices13 InfiniBand Cable with Pinch Connector Managing the System Connecting Ethernet Management DevicesInstalling the Switches Managing the System OL-10853-01 Failed Power Supply Modules Installing Field Replaceable UnitsPower Supply Modules Locating the Power Supply UnitRemoving a Filler Panel from the Switch Installing a Power Supply ModuleRemoving the Power Supply from the Switch Pull the unit from the bay Removing Power Supply ModulesColor Indication Managing the SwitchLEDs Chassis Status LEDsBi-color chassis status LED InfiniBand Port LEDs Power Supply LEDs2describes the InfiniBand Port LED operation Managing the System with Element Manager Power Supply and Fan LEDs LocationUsing the Power Supplies Tab Using the Summary TabUsing the Fans Tab Displaying System Information Using the Sensors TabDisplaying Power Supply Information SFS-7000P#show power-supplyDisplaying Sensor Information Displaying Fan InformationOL-10853-01 Self-Tests Hardware Diagnostic TestsAbout Diagnostic Tests LED TestsRunning Card Self-Test SFS-7000P#show diagnostic cardRunning Chassis Self-Test SFS-7000Pconfig#diag chassis test standardSFS-7000P-1#show diag post Running Fan Self-TestSFS-7000P#show diagnostic fan Enter the diag fan id commandDiag Fan Running Power Supply TestsReboot the chassis when the self-test is complete Diag Fru-errorRunning a Self-Test on a Power Supply Running a LED Test on the Power SupplyStart the test Enable Displaying Hardware ErrorsMore sysloghwiflog Power supply I2C communication error Error Number DescriptionPower supply DC fail error Power supply fan fail errorOL-10853-01 Specification Specifications and Compliance CertificationsChassis and Management Interface Category Specification Electrical SpecificationsAcronym Expansion Acronyms and AbbreviationsAppendix B Acronyms and Abbreviations IN-5 D E IN-6 IN-7 Nonvolatile memoryIN-8 IN-9 IN-10

Related manuals

Manual 7 pages 62.58 Kb